Electrolux EVE602 Installation Manual

Also see for EVE614: User manual User manual User manual User manual Quick start guide

WARNINGThe appliance must not be installed behind a decorative door inorder to avoid overheating.To avoid any potential hazard, you must follow our instructionswhen you install your appliance. Failure to install the appliancecorrectly could invalidate any warranty or liability claims and leadto prosecution.Use an authorised personAs stated in the local municipal building codes and other relevantstatutory regulations:• Wiring connections must be in accordance with AS/NZS 3000Wiring Rules and any particular conditions of the local authority.• Refer to data plate for rating information. The data plate ispositioned behind the bottom of the oven door.• For appliances with open cooking surfaces, a disconnect functionalswitch should be provided near the appliance in an accessibleposition. Refer to AS/NZS 3000 clause 4.7.1• Wiring should be protected against mechanical failure. Refer to AS/NZS3000 clauses 3.3.2.6, 3.9, 3.10• A means of disconnection with a contact separation of at least3mm must be supplied in the fixed wiring.• This appliance must be connected with cable of 75°C ratingminimum.• This product has passed the insulation resistance test aftermanufacture. If the resistance reading is low at installation, itis probably caused by moisture from the atmosphere beingabsorbed by the elements after the appliance has been produced.(pass at 0.01MΩ AS/NZS 3000 Wiring Rules Clause 8.3.6.2).WARNINGThis appliance must be properly earthed.• Do not lift the appliance by the door handles.• Prepare the cupboard opening to match your appliancemeasurements. (See diagrams)• Slide appliance into the cupboard, ensuring that the supply cable(where fitted) does not kink.• To prevent tipping, use the screws supplied to secure yourappliance into the cupboard by fastening through the 4 holes tothe front panel.• Where the appliance is built into a cabinet, the cabinet must becapable of withstanding 70°C. Installation into low temperaturetolerant cabinetry (e.g. vinyl coated) may result in deterioration ofthe low temperature coating by discolouring or bubbling.• If the appliance is to be installed adjacent to vinyl wrappedsurfaces, use an installation kit available from the vinyl-wrapsupplier.• Electrolux Home Products cannot accept responsibility for damagecaused by installation into low temperature tolerant cabinets.• After installation, test and ensure that the appliance operatescorrectly before handing it over to the customer.NOTE: If a powerpoint is fitted it must be accessible with the applianceinstalled, as the plug must be accessible after installation.Cabinet construction for your applianceFor the best integration within a kitchen, install this appliance in astandard 600mm wide cupboard that gives a flush fit (Figure A) with thesurrounding cupboard fronts. Non-pyrolytic appliances can also beinstalled using a proud fit (Figure B).IMPORTANTFor all Pyrolytic clean models, the oven must be installed as aflush fit (Figure A) to the surrounding cupboards and the “infillpanel” MUST not exceed 100mm in length. This ensures a 16mmgap is maintained between the cabinet and side of the applianceto prevent the cupboard overheating.Figure A – Flush Fit568mm568mmCupboarddoorCupboarddoor20mm600mm600mmOvenOven16mm16mmInfill panelInfill panel100mm maxfor pyrolytic ovenFigure B – Proud FitNOTE: Your appliance must be mounted on a flat horizontal surfacefor the full width and depth of the productLevelling ovenPlace a level in the oven as below making sure the level sits on thefront and rear forms. The level needs to be correct to prevent slidesfrom moving in or out with gravity.✓© 2020 Electrolux Home Products Pty Ltd. ABN 51 004 762 341 E_INS_Underbench_A4_Jun20 A20803501 Rev ATo access your detailed user manualsimply scan the QR code on yoursmart phone or visit electrolux.com.au/support/manuals/Installation guideBuilt-in ovens

/ 2

Related manuals for Electrolux EVE614