Electrolux 316488524 Installation, Use & Care Manual

Contents

1616161616Special functionsClock prClock prClock prClock prClock programmingogrammingogrammingogrammingogramming• The clock can be reprogrammed at any time except during an active timed function.• The clock can be displayed in a twelve hour format and valid clock times are from 1:00 to 12:59.• The clock can be reprogrammed pressing the “TTTTTimerimerimerimerimer” button for 5 seconds, and after, the clock can beadjusted with the “ ” and “ ” buttons. Colon “:” will flash indicating clock programming mode.• The user can have minute increments / decrements of 1 minute, but if the user keep pressing the “ ”/” ” buttons for more than 1 second, the increments / decrements will be of 5 minutes.During this option the control will round to the nearest 5 minutes.• The user can finish on reprogramming the clock pressing the “TTTTTimerimerimerimerimer” button.• After 1 minute of no button pressed the control will accept the programmed clock time and will add oneminute to the set clock.GrGrGrGrGrease filter saturation alarmease filter saturation alarmease filter saturation alarmease filter saturation alarmease filter saturation alarm• After thirty fan functional hours, the display will show “GrGrGrGrGrease Filterease Filterease Filterease Filterease Filter” if the fan is active.When this icon is shown in the display, the grease filters installed are required to be washed.• To reset the grease filter saturation alarm the user must press the “ ” button for 5 seconds, after thisaction the icon “GrGrGrGrGrease filterease filterease filterease filterease filter” is not displayed, and the hood has the normal display operation.CharCharCharCharCharcoal filter saturation alarm (Recircoal filter saturation alarm (Recircoal filter saturation alarm (Recircoal filter saturation alarm (Recircoal filter saturation alarm (Recirculating accessories)culating accessories)culating accessories)culating accessories)culating accessories)• After one hundred and twenty functional hours of the fan, the display will show “CharCharCharCharCharcoal Filtercoal Filtercoal Filtercoal Filtercoal Filter” if the fanis active. When this icon flashes on display, the charcoal filters installed are required to be replaced orreactivated.• To reset the charcoal filter saturation indication the user must press the “ ” button for 5 seconds, afterthis time the icon “CharCharCharCharCharcoal filtercoal filtercoal filtercoal filtercoal filter” is not displayed and the hood has the normal display operation.Audible signal activation and deactivationAudible signal activation and deactivationAudible signal activation and deactivationAudible signal activation and deactivationAudible signal activation and deactivation• The audible signals can be activated or deactivated pressing the “LightLightLightLightLight” button for 5 seconds.• If the audible signal is activated, a tone must sound and the “SndSndSndSndSnd” symbol must appear on the display for2 seconds.• If the audible signal is deactivated, the “SndSndSndSndSnd” symbol must appear on the display for 2 seconds and notone must sound.CharCharCharCharCharcoal filter inclusion and exclusion (Recircoal filter inclusion and exclusion (Recircoal filter inclusion and exclusion (Recircoal filter inclusion and exclusion (Recircoal filter inclusion and exclusion (Recirculating accessories)culating accessories)culating accessories)culating accessories)culating accessories)• The charcoal filter inclusion or exclusion can be set by pressing the “ ” and “ ” buttons at the sametime for 5 seconds.• The Inclusion or exclusion of charcoal filter must be selected while the lamps and the motor are OFF.• When the charcoal filter has been excluded, the charcoal filter alarm is disabled.Heat sensorHeat sensorHeat sensorHeat sensorHeat sensor• The control is equipped with a heat sensor that will turn on the blower at second speed if excessive heatoccurs (over 158° F158° F158° F158° F158° F or 70°C70°C70°C70°C70°C) surrounding the control area.• If the blower is OFF or if it is operating at first speed, the blower will be set automatically to second speed,the display shows the word "CArECArECArECArECArE" to indicate that heat sensor has detected an excessive heat.• During this state, the user may raise the blower speed to third speed but can not decrease the speed.• When the temperature level on the hood drops to normal, the blower will operate in the setting defined bythe user before the alarm occured.Control buttons - Special functions