D-Link DSN-4100 Series Quick Start Manual

Also see for DSN-4100 Series: Cli user's guide Software user's guide Manual Hardware reference guide Technical specifications

Contents

what else you need

Page 1DSN-4100 / DSN-4200 - 8/2011 Copyright © 2011 D-Link, Inc., All Rights ReservedDSN-4100/DSN-4200Series Quick Start GuideThis Quick Start Guide provides the information needed to getyour DSN-4100/DSN-4200 storage system out of the box andoperational with a direct connection to a host computer.Follow the simple instructions in this guide, and in no time atall you will be part of the iSCSI revolution.The DSN-4100/DSN-4200 storage system supports 16 3½-inchSAS or SATA hard disk drives, and it is expandable up to 80drives when used with DSN-4000 Expansion Arrays. It isavailable with either four or eight 1-Gigbit iSCSI data ports.Important Safety Information:Before you install the DSN-4100/DSN-4200 storage system,please read all documentation provided on the Product CD.1 Unpack the Package ContentsBefore unpacking, inspect the outer shipping carton fordamage. If any damage exists, file a claim with the carrier.Remove the items from the shipping carton and compare themto the packing list: The DSN-4100/DSN-4200 storage system with 16 empty drivecarriers and mounting screws One rack-mount kit in a box (includes rails, mountinghardware, and instructions) Two AC power cords for your country and one RS-232diagnostic cable. A Product CD containing installation and operation information,and tutorials Additional documentation (may include warranty information,End-User License Agreement and product registration information)If any contents are missing or damaged, please contact yoursupplier. Save all of the packing materials in case you need toreturn the unit.2 What Else You NeedTo complete the installation, you need the following items: One or more computer systems that will act as the iSCSI initiators(see step 6). Please refer to the D-Link Interoperability matrixat: http://www.dlink.com for a list of compatible operatingsystems, Network Interface Cards (NIC’s), Host Bus Adapters(HBA’s), and network infrastructure A static IP address and CAT5E or CAT6 network cable for each1GbE iSCSI data port that will connect to your SAN Independent AC power supply within 6 feet (2 meters) of the DSN-4100/DSN-4200 storage system SAS or SATA Disk drives: refer to the DSN-4000_Series HardwareReference Guide for instructions for drive installation. Optional: In addition, a separate computer may be used as theManagement console (refer to Step 7) Optional, but recommended: Uninterruptible power supply Optional: Ethernet switch3 Rack-Mount InstructionsThe DSN-4100/DSN-4200 storage system can be mounted in astandard 19-inch rack using the Rack-Mount Kit that is includedwith the product. The rack cabinet must provide sufficient airflowto the front and back of the DSN-4100/DSN-4200 storage system tomaintain correct cooling. It must include ventilation sufficient toexhaust the heat generated by equipment in the rack. Always planthe installation with the heaviest item on the bottom of rack.A. Ensure that power is not being applied by removing the AC powercords and attaching the mounting hardware provided to the leftand right sides of the rack supporting the DSN-4100/DSN-4200storage system.B. With the help of another person, slide the DSN-4100/DSN-4200storage system into place and secure with the mounting hardware.4 Install the Enclosure and Hard DrivesThe DSN-4100/DSN-4200 is a full iSCSI storage system, supportingup to 80 3½-inch SAS or SATA hard disks drives. The EnclosureStatus and Drive Status LED’s are on the front of the unit. The twoPower switches, Reset button, Mute Audio Alarm button, networkdata ports, and port speed and activity LED’s are on the rear panel.FrontViewRear View (8-port configuration shown)To install the hard drives into the drive carriers:A. Remove each empty drive carrier by squeezing the release latchand pulling the drive carrier out of the enclosure.Driver CarrierB. Place the hard drive into the drive carrier and attach it using fourmounting screws through the sides of the drive carrier (two screwson each side).C. Gently insert the assembled drive carrier into the enclosure untilthe latching mechanism engages with the chassis.For more detailed information, please refer to the DSN-4000_SeriesHardware Reference Guide, which is available on the Product CD.QUICKSTARTGUIDEReset & Mute ButtonsPower SwitchesStatus LED’sRelease LatchEnclosure Status LED’sDrive CarriersiSCSI Data PortsManagement Port SASExpansionPort

/ 2

Related manuals for D-Link DSN-4100 Series