Craftsman ZTS 6000 Quick Start Manual

Figure 10FILLADDSetting Up the Ground Speed Control Levers1. Loosen (do not remove) the hardware (J, Figure 7) securing the ground speedcontrol levers to the lever bases.2. Raise the levers, aligning the upper hole in each lever with the upper slottedhole in the lever base.3. Install the hardware (K) as shown in Figure 8. Tighten to 15-17 ft-lbs (20-23Nm).NOTE: Ground speed control levers must be adjusted prior to use. Refer to the“Ground Speed Control Lever Adjustment” section in the Operator’s manual.Check the Tire PressureReduce the tire pressures to the pressures as shown below. Tires are over-inflated forshipping purposes and must be set to the correct pressures for optimum traction.Rear Tire Pressure: 10-12 PSI Front Tire Pressure: 18-20 PSICheck Engine Oil LevelNote: Engine is shipped with oil. Add 10W-30 premium engine oil if oil level is low.See Operator’s Manual for complete engine oil specifications and maintenancerequirements.1. Lift the seat deck (L, Figure 9) to access the engine compartment.2. Clean the area around the dipstick/oil fill tube (M, Figure 10). Remove thedipstick and wipe with a clean rag.3. Insert the dipstick into the oil fill tube (thread in or push down completely).4. Remove and check the engine oil level. Oil level should be between Full andadd oil if necessary.5. Replace and fully secure the dipstick.Oil Capacity 21HP Briggs & Stratton: 48 ounces (1.42L) with oil filterOil Capacity 26HP Briggs & Stratton: 64 ounces (1.90L) with oil filterCharge BatteryLift the seat deck (Figure 9) to access the battery. If the unit is being put intoservice after the month and year indicated on the battery date tag (located on topof battery) charge the battery before use. Refer to the SERVICE & ADJUSTMENTSsection of this manual for battery charging information.Fill-Up with FRESH GasolineUse only unleaded gasoline with a minimum of 87 Octane.1. Remove the fuel tank cap and fill the tank with fresh fuel (Figure 10). Afterfueling, securely install the cap and wipe up any fuel that may have spilled.See the Operator’s Manual for complete fuel recommendations.Note: The single most common service issue is stale or contaminated fuel! Fuelshould not be more than 30 days old. Use fuel stabilizer to extend the freshness ofyour fuel, and always store fuel in an approved container. Stale fuel clean-out is notcovered under your warranty.Fuel Tank Capacity: 4 Gallons (15,14 L)QUICKSTART GUIDEZTS 6000C950-60929-0 (21HP Briggs & Stratton with 42” Mower)C950-60928-0 (26HP Briggs & Stratton with 52” Mower)Fuel TankCapThrottle /Choke ControlIgnition SwitchMower BladeSwitchParkingBrake LeverMower CuttingHeight SwitchItems Included:■ Operator’s Manual■ KeysMake sure you have all itemsbefore assembly.TransmissionRelease LeversRightGround SpeedLeftGround Speed& ControlLeverDANGER• Be sure blade(s) and engine are stoppedbefore placing hands or feet near blade(s).• When leaving machine, shut off, remove key,and set parking brake.Amputation hazardRotating blades cut off arms and legs.• Stop the mower when children or others are near.• Do not carry riders (especially children) even with theblades off. They may fall off or return for another ridewhen you are not expecting it.• Look down and behind before and while backing.• Read the operator's manualbefore using this product.10º Max.10º Max.Fire hazardGasoline is flammable. Yard debris is combustible.• Allow engine to cool for at least 3 minutes before refueling.• Keep unit cleaned of debris.Roll-over hazardOperating on slopes can cause loss of control and roll-overs.• If you cannot back-up a hill, do not drive on it.• If machine stops while going uphill, turn the blades off andback down slowly.• Avoid sudden turns.• Go up and down slopes, not across.Carbon monoxide hazardThe engine emits poisonous carbon monoxide gas.• Avoid inhaling exhaust fumes.• Only operate outdoors.WARNINGAvoid serious injury or death:• Know the location and function of all controls.• Keep safety devices (guards, shields, switches, etc.) in place and working.• Remove objects that could be thrown by the blade.For Assembly You Will Need:• Utility knife• Pry Bar• Tin Snips or Banding Cutter• Unleaded Fuel• 6-10 amp Battery Charger• Tire Pressure Gauge1© Sears Brands, LLC.Every effort has been made to ensure that the information in this document is accurate and current.However, we reserve the right to change, alter or otherwise improve the product and this documentat any time without prior notice.7103402-ARevision: ARev. Date 4/2009234567JFigure 7Figure 8KMLFigure 98910Call Customer Service Toll-Free 1-800-659-5917STILL HAVE QUESTIONS? Do not return to store. We can help.7103400Revision -Rev. Date 04/2009Operator’s ManualZTS 6000Zero-Turn Rear Engine Riders with Electric StartModel No.C950-60929-0 (21HP Briggs & Stratton Engine with 42" Mower)CAUTION: Before using this product, readthe manual and follow all its Safety Rules andOperating Instructions.For answers to your questions about thisproduct call:1-800-659-5917Sears Craftsman Help Line5 am - 5 pm, Mon - SatSears Canada Inc., Toronto, Ontario M5B 2C3Visit our Craftsman website: www.sears.ca/craftsmanAFigure 1Figure 2B EDCFFigure 3Figure 4Remove the Packaging MaterialsRemove the cardboard from the crate. Remove any steel banding securing theunit to the crate. Locate the manual packet.Read the Operator’s ManualLocate the operator’s manual in the manual packet. You should always readand follow the instructions in the operator’s manual. Proper care, performancetips, and safety information are located in this important document.Installing the Seat1. Raise the seat base (A, Figure 1).2. Align the holes (B, Figure 2) in the seat bottom with theholes (C) in the seat base.3. Secure the seat to the seat base with two 5/16-18 x 3/4 (D)serrated head bolts for the rear seat slots, andtwo 5/16-18 x 3/4 (E) shoulder bolts for the front slots.4. Tighten to 14-19 ft-lbs (19-25 Nm).Installing the Seat Safety Switch1. Insert the switch (F, Figure 3) into the slot (G) in the seat bot-tom. Push down past tabs (H) and slide up. Pull switch out tolock into place (see Figure 4).2. Insert the harness terminal housing (I, Figure 5) to the seatswitch. Allow tab on harness terminal housing to lock into placeon switch (see Figure 6).DANGER: CHECK RIDER SAFETY SYSTEM in Operator’s Manual.G HFigure 5IFigure 6Drive the Unit Off Crate1. Refer to the STARTING THE ENGINE SECTION of the manual for proper procedures.2. Use the mower cutting height switch to raise the mower deck to its highest cutting height.3. Pull the ground speed control levers in to DRIVE positions and slowly move them forward to drive the unit off the crate.When you are off the crate, return the ground speed control levers to their START/PARK positions.WARNING: Towing the unit will cause transmission damage. Do Not use anther vehicle to push or pull this unit. Do Notuse this unit to push or pull another vehicle or object.Read Manuals Before Starting EngineFollow procedures and safety instructions in Operator’s manual.Not forReproduction

/ 2

Related manuals for Craftsman C950-60928-0