Craftsman CMCB1150 Instruction Manual

7EnglishThree Year Limited WarrantyCRAFTSMAN will repair or replace, without charge, anydefects due to faulty materials or workmanship for threeyears from the date of purchase (two years for batteries).This warranty does not cover part failure due to normal wearor tool abuse. For further detail of warranty coverage andwarranty repair information, visit www.craftsman.comor call 1‑888‑331‑4569. This warranty does not apply toaccessories or damage caused where repairs have beenmade or attempted by others. THIS LIMITED WARRANTYIS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIEDWARRANTY OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTALOR CONSEQUENTIAL DAMAGES. Some states do not allowlimitations on how long an implied warranty lasts or theexclusion or limitation of incidental or consequentialdamages, so these limitations may not apply to you. Thiswarranty gives you specific legal rights and you may haveother rights which vary in certain states or provinces.Register OnlineThank you for your purchase. Register your product now for:• WARRAnTY sERViCE: Registering your product willhelp you obtain more efficient warranty service in casethere is a problem with your product.• COnFiRMATiOn OF OWnERshiP: In case of aninsurance loss, such as fire, flood or theft, your registrationof ownership will serve as your proof of purchase.• FOR YOUR sAFETY: Registering your product will allowus to contact you in the unlikely event a safety notificationis required under the Federal Consumer Safety Act.• Register online at www.craftsman.com/registrationRepairsThe charger, battery pack, and power inverter are notserviceable. There are no serviceable parts inside the chargeror battery pack. WARNING: To assure product SAFETY and RELIABILITY,repairs, maintenance and adjustment (including brushinspection and replacement, when applicable) shouldbe performed by a CRAFTSMAN factory service centeror a CRAFTSMAN authorized service center. Always useidentical replacement parts.Accessories WARNING: Since accessories, other than thoseoffered by CRAFTSMAN, have not been tested withthis product, use of such accessories with this toolcould be hazardous. To reduce the risk of injury, onlyCRAFTSMAN recommended accessories should be usedwith this product.Recommended accessories for use with your tool areavailable at extra cost from your local dealer or authorizedservice center. If you need assistance in locating anyaccessory, please contact CRAFTSMAN call 1‑888‑331‑4569.Cleaning WARNING: Never use solvents or other harshchemicals for cleaning the non‑metallic parts of thetool. These chemicals may weaken the plastic materialsused in these parts. Use a dry cloth only. Never let anyliquid get inside the tool; never immerse any part of thetool into a liquid.MAINTENANCE WARNING: To reduce the risk of serious personalinjury, turn unit off and remove the battery packbefore making any adjustments or removing/installing attachments or accessories. Anaccidental start‑up can cause injury.Your CRAFTSMAN power tool has been designed to operateover a long period of time with a minimum of maintenance.Continuous satisfactory operation depends upon proper toolcare and regular cleaning.Overload and Overtemperature:• When an overload or overtemperature occurs, theinverter will automatically turn off.• The power LED 9 on the power button 8 will light andwill remain lit for about 1 minute.• If continuing use of the device, turn the power inverteroff, reduce the load, or allow the inverter to rest orcool down.Worklight (Fig. A) CAUTION: Do not stare into worklight. Serious eyeinjury could result.• Press the worklight power button 11 to turn on theworklight 10 and ports 3 and 4 .• Turn the worklight off by pressing the worklight powerbutton a second time. This will also turn off the ports.nOTE: The worklight is for lighting the immediate worksurface and is not intended to be used as a flashlight.nOTE: AC output will be turned off automatically after30 minutes when there is no load, the connected devices isinactive, or the load is less than 7W. At the same time, thegreen light of the power LED 9 will turn off.nOTE: This device is not compatible for use with appliances,power tools, air conditioners, sump pumps, compressors,and/or other larger electrical devices.Charging a Device (Fig. A)1. Open either the Type A and C port cover 6 or the AC portcover 7 .2. Insert a plug into the appropriate port to supply power orcharge your devices.3. Press the power button 8 to turn on the power inverter.The power LED 9 will turn on. This will provide power to orcharge the device plugged in.4. Press the power button a second time to turn it off. Thepower LED will turn off.