Craftsman 315.175070 Owner's Manual

RULES FOR SAFE OPERATION (Continued)M PROTECT YOUR LUNGS. Wear a face or dustmask if the operation is dusty.M PROTECT YOUR HEARING. Wear heatingprotection during extended pedods of operation.= DO NOT ABUSE CORD. Never carry tool bycord or yank it to disconnect from receptacle.Keep cord from heat, oil, and sharp edges.= SECURE WORK. Use clamps or a vise to holdwork. It is safer than using your hand and it freesboth hands to operate tool.n DO NOT OVERREACH. Keep proper footing andbalance at all times. Do not use on a ladder orunstable support. Secure tools when working atelevated positions.= MAINTAIN TOOLS WITH CARE. Keep toolssharp and clean for best and safest performance.Follow instructions for lubricating and changingaccessories.B DISCONNECT TOOLS. When not in use, beforeservicing, or when changing attachments, toolsshould be disconnected from power supply.• REMOVE ADJUSTING KEYS ANDWRENCHES. Form habit of checking to see thatkeys and adjusting wrenches are removed fromtool before turning it on.• AVOID ACCIDENTAL STARTING. Do not carryplugged-in tool with finger on switch. Be sureswitch is off when plugging in.n MAKE SURE YOUR EXTENSION CORD IS INGOOD CONDITION. When using an extensioncord, be sure to use one heavy enough to carrythe current your product will draw. An undersizedcord will cause a drop in line voltage resulting inloss of power and overheating. A wire gage size(A.W.G.) of at least 12 is recommended for anextension cord 50 feet or less in length. A cordexceeding 100 feet is not recommended. If indoubt, use the next heavier gage. The smallerthe gage number, the heavier the cord.n OUTDOOR USE EXTENSION CORDS. Whentool is used outdoors, use only extension cordssuitable for use outdoors. Outdoor approvedcords are marked with the suffix W-A, forexample - SJTW-A or SJOW-A.M KEEP CUTTERS CLEAN AND SHARP. Sharpcutters minimize stalling and kickback.M KEEP HANDS AWAY FROM ROUTING AREA.Keep hands away from cutters. Do not reachunderneath work while cutter is rotating. Do notattempt to remove material while cutter is rotating.m NEVER USE IN AN EXPLOSIVEATMOSPHERE. Normal sparking of the motorcould ignite fumes.• INSPECT TOOL CORDS PERIODICALLY and ifdamaged, have repaired at your nearest SearsRepair Center. Stay constantly aware of cordlocation.B INSPECT EXTENSION CORDSPERIODICALLY and replace if damaged.n KEEP HANDLES DRY, CLEAN, AND FREEFROM OIL AND GREASE. Always use a cleancloth when cleaning. Never use brake fluids,gasoline, petroleum-based products, or anystrong solvents to clean your tool.B STAY ALERT AND EXERCISE CONTROL.Watch what you are doing and use commonsense. Do not operate tool when you are tired.Do not rush.MmB CHECK DAMAGED PARTS. Before further useof the tool, a guard or other part that is damagedshould be carefully checked to determine that itwill operate properly and perform its intendedfunction. Check for alignment of moving parts,binding of moving parts, breakage of parts,mounting and any other conditions that mayaffect its operation. A guard or other part that isdamaged should be properly repaired or re-placed by an authorized service center.B DO NOT USE TOOL IF SWITCH DOES NOTTURN IT ON AND OFF. Have defective switchesreplaced by an authorized service center.B INSPECT FOR and remove all nails from lumberbefore routing.n DO NOT operate this tool while under theinfluence of drugs, alcohol, or any medication.B POLARIZED PLUGS. To reduce the risk ofelectric shock, this tool has a polarized plug (oneblade is wider than the other), This plug will fit ina polarized outlet only one way. If the plug doesnot fit fully in the outlet, reverse the plug. If it stilldoes not fit, contact a qualified electrician toinstall the proper outlet. Do not change the plugin any way.WHEN SERVICING USE ONLY IDENTICALCRAFTSMAN REPLACEMENT PARTS.mmWHEN USING THIS ROUTER WITH AROUTER TABLE, HELP PREVENT POSSIBLESERIOUS INJURY BY KEEPING THE CUTTERGUARDED AT ALL TIMES. Use only routertables, with guards, that have been designed foruse on routers that are of this type, size, andweight.DO NOT USE TOOL UNDER "BROWN-OUT"OR OTHER LOW VOLTAGE CONDITIONS.Also, do not use with any device that couldcause the power supply voltage to change.SAVE THESE INSTRUCTIONS. Refer to themfrequently and use them to instruct others whomay use this tool. If you loan someone this tool,loan them these instructions also.4