Craftsman 172.341201 Operator's Manual

6SAFETY INSTRUCTIONS cont.EXTENSION CORDSUse a proper extension cord. ONLY use cords listed by Underwriters Laboratories (UL).Other extension cords can cause a drop in line voltage, resulting in a loss of powerand overheating of tool.For this tool an AWG (American Wire Gauge) size of a least 14-gauge is recommendedfor an extension cord of 25-ft. or less in length. Use 12-gauge for an extension cordof 50-ft. Extension cords 100-ft. or longer are not recommended.WARNING: GFCI (Ground Fault Circuit Interrupter) protection should beprovided on all circuits or outlets to be used for electric chain saws and lawn andgarden power tools. Receptacles are available having built-in GFCI protection andshould be used for this measure of protection.• Double insulation DOES NOT take the place of normal safety precautions whenoperating this tool.• Guard against electric shock: Prevent body contact with grounded surfaces.For example: metal pipes, wire fences.!3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within the voltagemarked on the tool’s data plate. DO NOT use “AC only” rated tools with a DC power supply.4. DO NOT expose tools to rain or wet conditions or use electric tools in wet or damplocations. Water entering an electric tool will increase the risk of electric shock.5. If operating an electric tool in damp locations is unavoidable, ALWAYS USE aGround Fault Circuit Interrupter to supply power to your tool. ALWAYS WEARelectrician’s rubber gloves and footwear in damp conditions.6. To reduce the risk of electric shock, use only with an extension cord intended for outdoor use,such as an extension cord of cord type: SW-A, SOW-A, STW-A, STOW-A, SJW-A,SJOW-A, SJTW-A. or SJTOW-A.7. INSPECT tool cords for damage. Have damaged tool cords repaired at a Sears Service Center.BE SURE to stay constantly aware of the cord location and keep it well awayfrom the cutting blade.8. DO NOT abuse the extension cord. NEVER use the cord to carry the tool by or topull the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts.Replace damaged cords immediately. Damaged cords increase the risk of electric shock.ELECTRICAL SAFETYWARNING: Do not permit fingers to touch the terminals of plug wheninstalling or removing the extension cord from the plug.!1. Double insulated tools are equipped with a polarized plug(one blade is wider than the other and will require the use of apolarized extension cord. The Chain Saw’s plug will fit into apolarized extension cord only one way. If the plug does not fit fully intothe extension cord, reverse the plug. If the plug still does not fit, obtaina correct polarized extension cord. A polarized extension cord will require the use of a polarizedwall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fitfully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualifiedelectrician to install the proper outlet. Do not change or alter the equipment plug,extension cord receptacle, or extension cord plug in any way.2. Double insulation eliminates the need for the three-wire grounded power cord andgrounded power supply system. Applicable only to Class II (double-insulated) tools.This Chain Saw is a double insulated tool.7SAFETY INSTRUCTIONS cont.Remember, a smaller wire gauge size has greater capacity than a larger number(14-gauge wire has more capacity than 16-gauge wire; 12-gauge wire hasmore capacity than 14-gauge). When in doubt use the smaller number.! CAUTION: Keep the extension cord clear of the work area. Position the cord so that it willnot get caught on bushes, hedges, tree trunks, lawnmowers or other obstructions while you areworking with the Chain Saw.WARNING: Check extension cords before each use. If damaged replace immediately.Never use tool with a damaged cord since touching the damaged area could cause electricalshock, resulting in serious injury.!SAFETY SYMBOLS FOR YOUR TOOLEXTENSION CORDS cont.The label on your tool may includethe following symbols.Remove plug from mains immediatelyif the cable is damaged or cut.V................VoltsA................AmpsHz..............HertzW...............Wattsmin............Minutes.............Alternating current...........Direct currentno ............ No-load speed.../min.......Revolutions or Strokes per minute.............Indicates danger, warning or caution.It means attention! Your safety isinvolved.Contact of the guide bar tip withany object should be avoided..........Tip contact may cause the guidebar to move suddenly upwardand backwards, which may causeserious injury to user..........Read and follow all safetyprecautions in the owner’s manualFailure to follow to instructioncould result in serious injury to user..........Do not expose to rain...................Do not use one handed whenoperating the chain saw................... Correct Direction of Cutting-Teeth..........Chain Stop.........Protective goggles/visor,helmet & hearing protection..........Gloves with saw protection..........Boots with saw protection,steel-toe cap and non-slip sole..........Always use two hands whenoperating the chain saw..........The chain saw kickback angleis 10 , with a chain stop.10º..........Class II construction,Double-Insulation. When servicing,use only identical replacement parts.......... Wear dust mask.Minimum guage for extension cordsMethod of securingextension cord