D15327.01 MX800 Dual Replacement Guide, MAY 2015. www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.1Cisco TelePresence MX800 Dual Replacement GuideReplacement guidefor Cisco TelePresence MX800 Dual

Introduction

Grilles and covers

Replace speaker grille and lower grille

Replace floor stand covers

Replace side covers

Replace center top profile, camera cover and center back cover

Re-assembly

Speakers and cameras

Replace a loudspeaker

Step 2: Remove the loudspeaker

Replace dual camera module

D15327.01 MX800 Dual Replacement Guide, MAY

Codec and monitors

Replace codec

Replace PoE injector

Replace monitor (mounted on a stand)

Replace monitor (wall mounted)

Appendix

Part numbers for spare parts

Cisco contacts

Cisco TelePresence MX800 Dual Replacement Manual

Telepresence MX800

best practice

tour the touch screen

log onto a system with your own credentials

Edit a Contact List Entry, then Place the Call

place call using name

place call using an ip address

place call using number

receive call

receive call while in another call

Transfer

consult and transfer

disconnect yourself from call

a few words on microphone behavior and privacy

put call on hold and resume a call on hold

change call rate

enable do not disturb

enable standby

view keypad while in a call

add additional participants to existing call

add incoming call to existing call

view meeting participant list

manage conference call layout

lock speaker

disconnect participant from call

Intelligent Proximity

Activate and Deactivate Intelligent Proximity

getting started

Change Presentation Layout In a Call

presentation outside calls

view meeting list

join scheduled meeting

parallel meetings

Contacts Directory

call recents

Favorites

Add Someone to Favorites, While in a Call

view camera settings

add camera position preset

edit existing camera position preset

speaker tracking

Snap to Whiteboard

PresenterTrack

control own camera

manage selfview

resize the selfview pip

move the selfview pip

control the camera of the other participant

gain access to the settings

Ringtone & Sound

camera control

main source selection

Display

select language

system information

call status

diagnostic mode

restart system

about administrator

Administrator Settings—Tracking

Administrator Settings—Set Date and Time

Administrator Settings—Call Details

Administrator Settings—Provisioning Wizard

Administrator Settings—Multipoint Mode

Administrator Settings—Pairing

Administrator Settings—IP & VLAN, Codec

Administrator Settings—Network Status Codec

Administrator Settings—IP & VLAN, Touch

Administrator Settings—Network Status Touch

Administrator Settings—SIP

Administrator Settings—H323

Administrator Settings—EMC Resilience Mode

Administrator Settings—Factory Reset

user guide

Produced: December 2014 for TC 7

Best Practice

Tour the Touch Screen

Log Onto a System with Your Own Credentials

video calls

Place Call Using Name

Place Call Using an IP Address

Place Call Using Number

Receive Call

Receive Call While in Another Call

Consult and Transfer

Disconnect Yourself From Call

A few words on microphone behavior and privacy

Put Call on Hold and Resume a Call on Hold

Change Call Rate

Enable Do Not Disturb

Enable Standby

View Keypad While in a Call

Add Additional Participants to Existing Call

Add Incoming Call to Existing Call

View Meeting Participant List

Manage Conference Call Layout

Lock Speaker

Disconnect Participant from Call

Share Content Start and Stop Presentation in a Call

Presentation Outside Calls

scheduled meetings

Scheduled Meetings View Meeting List

Join Scheduled Meeting

Parallel Meetings

Call Recents

View Camera Settings

Add Camera Position Preset

Edit Existing Camera Position Preset

Speaker Tracking

Control Own Camera

Manage Selfview

Resize the Selfview PiP

Move the Selfview PiP

Control the Camera of the Other Participant

Settings Gain Access to the Settings

Camera Control

Main Source Selection

Select Language

System Information

Call Status

Diagnostic Mode

Restart System

Administrator

About this guide

What's new in this version

About the API

API fundamentals

Telnet

API output

Using the command line

Command line shortcuts

Commands

Configurations

Status

Events

using http

Feedback mechanism

Translating from terminal mode to XML

Dos and don'ts

xConfiguration commands

Appendices

conference configuration

h323 configuration

sip configuration

xcommand commands

audio commands

call commands

peripherals commands

video commands

xstatus commands

description of the xstatus commands

h323 status

about startup scripts

the systemtools commands

about disconnect cause types

user documentation on the cisco web site

D15358.02 - JULY

In-room controls

Widgets

Toggle button

Slider

Button with custom text

Button with symbol

Text box

Statuses

troubleshooting

cisco contacts

APRIL

Connect to the video system

Spinner

Group button

Command reference

Troubleshooting

Development tools on the web interface

Tips and tricks

Examples

D15358.01 APRIL

intellectual property rights

Cisco TelePresence MX800 Dual Replacement Manual

Product

Learn More

Legal