Beyond Access:Enabling the Full-Service BranchQuick Reference Guide: Access RoutersCisco SOHO, 800, 1700, 2600, 3600,3700, 7200, 7300, and 7400 Series

cisco soho series and 800 series

ordering information

cisco 1700 series

product positioning

cisco 3600 series

remote management

interface cards

product transition matrix

Cisco SOHO series Quick Reference Manual

document conventions

additional information

obtaining documentation

ordering documentation

technical assistance center

Understanding Cisco IOS Software Basics

Undoing a Command or Feature

Saving Configuration Changes

Before Starting Your Router

Chapter 2 
 Using the Setup Command Facility

Configuring Interface Parameters

Ethernet Interface Configuration

Token Ring Interface Configuration

Frame Relay Encapsulation

ATM-DXI Encapsulation

Asynchronous Configuration

ISDN BRI Interface Configuration

ISDN BRI Line Configuration

Defining ISDN Service Profile Identifiers

E1 Channelized Mode

T1 Channelized Mode

Port, 4-Wire 56-kbps DSU/CSU Configuration Setup

Dedicated Mode

Where to Go Next

Configuring the Host Name and Password

C H A P T E R 3 Configuring with the Command-Line Interface

Configuring Fast Ethernet Interfaces

Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards

Configuring 16-Port and 32-Port Asynchronous Network Modules

Configuring ISDN BRI WAN Interface Cards

Configuring ISDN BRI Lines

Configuring T1 and E1 Interfaces

Configuring T1 Interfaces

Configuring E1 Interfaces

Configuring Codec Complexity

Configuring T1 (FT1) WAN Interface Cards

Configuring ATM Interfaces

Configuring SVCs

Configuring Inverse Multiplexing for ATM Interfaces

Configuring the ATM T1/E1 Interface

Configuring the IMA Interface

Checking the IMA Configuration

Checking the Modem Configuration

Checking the Interface Configuration

Benefits

Prerequisites

Verifying ATM Configuration

Configuration Examples

Configuring the NM-AIC-64, Contact Closure Network Module

Serial Communication Channels

Asynchronous Craft Port

Configuration Tasks

Accessing the AIC

Configuring Alarms

Programming the Discrete Contact Points

Troubleshooting Tips

Configuration Backup

Specify a HSSI

Convert HSSI to Clock Master

Cisco 3600 Series Routers

Configuration Example

Configure the E1/T1 Network Module for ISDN PRI

Configure Channelized T1 ISDN PRI

Configure the ISDN D-Channel Serial Interfaces

Configure the ISDN D-Channel Serial Interface for T1 Modules

Configure the LAN Interface

Configure the ISDN Dialer Interface

Configure the Default IP Pool Information

Configuring 1-Port G.SHDSL WAN Interface Card

Restrictions

Configuring G.SHDSL on a Cisco Router

Configuring ILMI on the DSLAM Connected to the ADSL WAN

Voice-over-IP Prerequisites

Configuring the Voice Interface

C H A P T E R 4 Configuring Voice-over-IP

FXS-to-FXS Connection Using RSVP

Configuration for Router RLB-w

Linking PBX Users with E&M Trunk Lines

Router SJ Configuration

PSTN Gateway Access Using FXO Connection

Router SLC Configuration

Configuring Direct-Inward Dialing on a BRI Port

Router 1 Configuration

Cisco 2600 Series Router Configuration Example

Appendix A  Configuration Example

Cisco 3631 Router Configuration Example

Cisco 3725 Router Configuration Example

Port ADSL WAN Interface Card Configuration Examples

VoATM over AAL5 on the ATM Interface Configuration Example

NM-AIC-64, Contact Closure NetworkConfiguration Examples

IP Route to the AIC Configuration Examples

Without an Unnumbered IP Address

AIC CLI Configuration for Alarms

Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

3600 Series

document organization

obtaining technical assistance

submitting a service request

obtaining additional publications and information

hardware documentation

where to go next

safety recommendations

preventing electrostatic discharge damage

summary of installation tasks

installing and removing gbics

ethernet leds

token ring leds

network modules

hardware and software requirements

laser safety guidelines

interfaces supported

subscriber unit

power considerations

port numbering

master led

planning the stack

additional references

saving the configuration file

feature overview

supported platforms

command reference

clear ip dhcp binding

ip dhcp ping packets

ip dhcp pool

ip dhcp relay information check

ip dhcp relay information option

service dhcp

show ip dhcp binding

syntax description

related commands

show ip dhcp server statistics

debug commands

debug ip dhcp server

product overview

Memory Configurations

Safety Recommendations

safety warnings

safety with electricity

Tools and Equipment Needed

removing sdram dimms

installing sdram dimms

Upgrading System Memory in Cisco 3745 Routers

replacing compactflash memory cards

Recovering Compact Flash Memory and System Images

Documentation Feedback

Obtaining Additional Publications and Information

Chapter 2 
 Preparing to Install the Router

hardware features

memory specifications

interface numbering

Cisco 3660 Interfaces

Voice Interface Numbering

Regulatory Compliance

Preventing Electrostatic Discharge Damage

General Site Requirements

Site Environment

Equipment Racks

Installation Checklist

Creating a Site Log

Tools and Equipment for Installation and Maintenance

Console and Auxiliary Port Considerations

Preparing to Connect to a Network

Token Ring Connections

Signaling Standards Supported

Asynchronous/Synchronous Serial Module Baud Rates

K/Switched-56-kbps DSU/CSU Connections

installing the router

Installing Modules, Interface Cards, and Power Supplies

Installing the Chassis

Attaching Brackets to the Router

Mounting the Router in the Rack

Wall-Mounting the Cisco 3620 Router

Installing Chassis Ground Connection

Cisco 3631 Chassis Ground Connection

Cisco 3660 Chassis Ground Connection

Power Connections

Wiring the DC-Input Power Supply in Cisco 3620 and Cisco 3640 Routers

Wiring the DC-Input Power Supply in Cisco 3631 Routers

Wiring the DC-Input Power Supply in Cisco 3660 Routers

Connecting Routers to the Cisco Redundant Power System

Connecting WAN, LAN, and Voice Cables

Connections for Cisco 3620, Cisco 3640, and Cisco 3631 Routers

Connecting WAN, LAN, and Voice Cables (With Chassis Shield—Telco Only)

Connecting to a Console Terminal or Modem

Connecting to the Console Port

Connecting to the Auxiliary Port

Identifying a Rollover Cable

Powering Up the Router

Cisco SOHO series Quick Reference Manual

Product

Learn More

Legal


Contents cisco soho series and 800 series ordering information cisco 1700 series product positioning cisco 3600 series remote management interface cards product transition matrix	Beyond Access:Enabling the Full-Service BranchQuick Reference Guide: Access RoutersCisco SOHO, 800, 1700, 2600, 3600,3700, 7200, 7300, and 7400 Series Next / 104