QUICK START GUIDECisco Service Control Engine 2000 4xGBE QUICK S TART G UIDE,RELEASE 3.8. X1 Preparing for Installation2 Rack-Mounting the SCE 2000 Chassis3 Connecting Power Supply Units4 Connecting Management Interfaces and Performing Initial System Configuration5 Cabling Line Ports6 Completing the Installation7 Troubleshooting8 Obtaining Documentation and Submitting a Service Request

site preparation

troubleshooting

Cisco 2000 4xGBE Quick Start Manual

document revision history

related publications

obtaining documentation

documentation feedback

the cisco service control concept

cisco service control capabilities

management and collection

network management

introduction to the sce platform

front panel

Back Panel

Checking the Shipping Container Contents

SCE 2000 Component List

SCE 2000 Installation Checklist

Topology

Functionality

Link Continuity

Physical Topologies

Two Cascaded SCE 2000s For Dual Links

Topology-Related Parameters

physically connected links parameter

Installation and Maintenance

Tools and Parts Required

Site Requirement Guidelines

Installing the SCE 2000 Platform

Installation Precautions

Rack-Mounting a SCE 2000 Platform

attaching the brackets to the sce

attaching the crossrail supports to the rack

mounting the system to the rack

Attaching a Chassis Ground Connection

Power Supply Overview

LEDs

Power Supply Specifications

Powering Down the Power Supply Unit and Disconnecting Input Power

Removing the Power Supply Unit

Replacing the Power Supply Unit

reconnecting ac-input power supply unit

reconnecting dc-input power supply unit

Fan Module Overview

removing the fan module

Replacing the Battery

Connecting the Management Interfaces and Performing Initial System Configuration

Setting Up the Local Console

Initial System Configuration

Index

Step 1: Configuring Initial Settings

Step 2: Configuring the Hostname

Step 4: Configuring Time Settings

Step 5: Configuring the DNS Settings

Step 6: Configuring the RDR Formatter Destination

Step 7: Configuring Access Control Lists (ACLs)

order of entries

Step 8: Configuring SNMP

Step 9: Configuring the Topology-Dependent Parameters

Step 10: Completing and Saving the Configuration

Connecting the Management Interface

Verifying Management Interface Connectivity

Cabling the Line Ports and Completing the Installation

Cabling Diagrams

Configuring the GBE Interface Parameters

Connecting the GBE Line Interface Ports

cabling the gbe port

Testing Connectivity: Examining Link LEDs and Counters

Installing a Cascaded System

CLI Commands

configuring the connection mode

link mode

Loading and Activating a Service Control Application

Basic SCE 2000 Platform Operations

Starting the System and Observing Initial Conditions

Final Tests

Managing SCE 2000 Configurations

Saving the Configuration Settings

Recovering a Previous Configuration

Performing Complex Configurations

Shutting Down the SCE Platform

Troubleshooting

Troubleshooting Tools

CLI Commands for Troubleshooting

The User Log

copying the user log

clearing the user log

Check the LEDs

Problem Solving Using a Subsystems Approach

Troubleshooting the Power Subsystem

Troubleshooting the Firmware Package Installation

Troubleshooting the Management Subsystem

Troubleshooting the Link Interface Subsystem

The External Optical Bypass Module

External Optical Bypass Functionality

The External Optical Bypass Module Front Panel

Installing the Module in a Rack

Specifications

CE 2000 Platform SCE 2000 4xGBE

Introduction

document conventions

obtaining additional publications and information

SCE Platform Management Interfaces

sce platform management interfaces

Overview of the SCE 2000 Platform

Service Control Management

Front Panel

sce 2000 configuration

Installing the SCE 2000 on a Workbench or Tabletop

Removing and Replacing a Power Supply Unit

powering down an ac-input power supply

Reconnecting the Power

Cabling the Management Port

monitoring the system

Rebooting and Shutting Down the SCE Platform

the user log

generating a file for technical support

sce 2000 operational status

Installing the External Bypass Module

Cabling the External Optical Bypass Module

about this guide

Information About the Cisco Service Control Concept

Chapter 1 
 General Overview

The SCE Platform

Information About Management and Collection

Network Management

Service Configuration Management

information about the sce platform

Chapter 2 
 Introduction to the SCE Platform

sce 2000 installation checklist

The SCE 2000 Platform

Chapter 3 
 Information About Topology

Bypass Mechanism

Asymmetric Routing Topology

Single Link: Receive-only Topology

Dual Link: Receive-Only Topology

Information About Two Cascaded SCE 2000s For Dual Links

Information About Topology-Related Parameters

Physically Connected Links Parameter

Information About Preparing to Install the SCE 2000 Platform

C H A P T E R 4 Installation and Maintenance

Information About Site Requirement Guidelines

How to Attach the Brackets to the SCE 2000

How to Attach the Crossrail Supports to the Rack

How to Mount the System to the Rack

How to Attach a Chassis Ground Connection

How to Power Down a DC-Input Power Supply Unit and Remove the DC-Input Leads

How to Remove the Power Supply Unit

How to Reconnect DC-Input Power Supply Unit

Removing and Replacing the Fan Module

Replacing the Fan Module

How to Replace the Battery

How to Set Up the Local Console

C H A P T E R 5 Connecting the Management Interfaces and Performing Initial System Configuration

Setup Command Parameters

Step 1: How to Configure Initial Settings

Step 2: How to Configure the Hostname

Step 4: How to Configure Time Settings

Step 5: How to Configure the DNS Settings

Step 6: How to Configure the RDR Formatter Destination

How to Configure Access Control Lists (ACLs)

Step 8: How to Configure SNMP

Step 9: How to Configure the Topology-Dependent Parameters

Step 10: How to Complete and Save the Configuration

How to Verify Management Interface Connectivity

Connecting the line ports to the network

Single Link: Inline Topology

C H A P T E R 6 Cabling the Line Ports and Completing the Installation

Dual Link: Two SCE 2000s Topology

How to Configure the GBE Interface Parameters

Fiber Specifications

the Device

How to View the Gigabit Ethernet Counters

Information About Cascaded Systems

CLI Commands for Cascaded Systems

How to Configure the Connection Mode

Monitoring the System

How to Load and Activate a Service Control Application

Starting the SCE 2000 Platform

Chapter 7 
 Basic SCE 2000 Platform Operation

How to View the User Log Counters

How to Save or Change the Configuration Settings

Example for Saving or Changing the Configuration Settings

How to Recover a Previous Configuration

How to Display the SCE Platform Version Information

How to Display the SCE Platform Inventory

Examples for Shutting Down the SCE Platform

Troubleshooting Overview

Chapter 8 
 Troubleshooting

Checking the LEDs

Troubleshooting with the User Log

How to Copy the User Log to an Internal Location

How to View the Non-volatile Logger Counters For Both the User Log File and the Debug Log File

Cisco 2000 4xGBE Quick Start Manual

Product

Learn More

Legal


Contents site preparation troubleshooting	QUICK START GUIDECisco Service Control Engine 2000 4xGBE QUICK S TART G UIDE,RELEASE 3.8. X1 Preparing for Installation2 Rack-Mounting the SCE 2000 Chassis3 Connecting Power Supply Units4 Connecting Management Interfaces and Performing Initial System Configuration5 Cabling Line Ports6 Completing the Installation7 Troubleshooting8 Obtaining Documentation and Submitting a Service Request Next / 28