Menu
Captain E202 User Manual
  |
eE202(Tuya WiFi)Smart Lock User ManualPlease read this manual carefully before useInformation & Safety WarningsNote: Please prepare a Phillips screw driver and 4 AA batteries beforeinstallation.1. Keep your fingers clean before using this product.2. In original settings, ii can be unlocked with any fingerprint, any card,or password" 1234567890' ended with'#'.3. Unlock: Press registered fingerprint on front handle sensor, or makecard close to lock pad, or enter password ended with"#".4. If the power is insufficient, there will be an alarm prompt, and the lockcan be only unlocked around 50 times, please replace with 4 newbatteries in time. When batteries power running out, connecting apower bank with Micro USB line though Emergency Power Port canunlock, but the APP network function will be failure.5. Please don·t use corrodent material to clean the surface.6. When the password/fingerprint/card/APP can not unlock the door,please use the key to unlock the door. Plee1111 keep the emergency keywith you or put it in outdoor safe place.7. Waking up lock needs around 3 seconds or more, when long time no using.B. The lock is suitable for 1.57 -3.94INCH thick doors.9. Work temperature range: -22'F ~ 131 ° F.Features1. The total capacity of system is 100, and the first three are administrator.2. Touching button, durable.3. Support 6-8 password and 20 virtual password.4. Support low power warning.5. Support volume adjustment and door bell.Name ParameterFingerprint Sensor semiconductor.DPI 500Identify lime O.C3SUnlock Way Fingerprint, Card, Password, Key and APPSystem Capacity 100Supply Voltage 6VLoW Voltage Warning 4.BVStandby Current <=50uAInstallation1. Installation Instructionsa. It is racommended lo look for professionals to install, watch the videocarefully before installing.b. Please note that the connection line can't be pressed or folded during.Installation.c. Before the installation, the lock must be selected correctly accordinglo the door opening direction, because the handle can't be adjusted.d. Whlle installing, the door must be in half open state until thecommissioning is completed.e. After the l/i.&tallat1011 is completed, when the fingerprint, card,password(1234567890) and#, APP, key unlock, test whether the fronthandle and back handle unlock/lock normally or not.f. If it does not work properly, please check if there is improper installationor the power cord is loose.2. Installation Overview� �l151617 181920211. Front Panel2.Connectlon Column3.Square St■-14.LockBody5.Connectlon Linefl,811ckP11nel1: SET' 9ulton8.Connection Column Screws9.Battery Cover1 O.Battery Cover screw11.Beck Handle12.Connecllon Column Screws13.Reverse Lock Knob14.Back Locking Peddle15.Dead-bolt16.Latch-bolt17 .Lock Body Screws18.Connecllon Column19.KeyHole20.Emergancy Power Port21.Front Handle3. Confirm The Direction of The DoorThis smart lock is suitable for Left Out/Left In/Right Out/Right In) 4 kinds of dooropening directions,LeftHandDoor l�r� Left InOutdoorIndoorRight Hand Door �doorc::::Y==C:C::J Righi InOutdoorLen outOu oor4.0pen HoleIndoor�RightOutOutdoorPlease refer to the opening hole drawing, and drill right holes on the door.5. Install Lock Body5.1. Choose the lnstelletlon direction of the latch-bolt of the lock body bythe door opening directions.�Left In/�Right Out5.2. Change the direction of lock bodya. Push the reversing block to the otherside.b. Push the latch-bolt into the lock andturn 180 degrees.c. Put back the reversing block, and thelatch-bolt will pop up automatically.�LeftOut/�Right ln,-· Latch-bolt0 @>-" ··Square SteelHole""Dead-bolt+Lock Body(5052)5.3. Put the lock body into the door frame and tighten 2 fixing screws. |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved