Caple CAFF60 Instruction Manual

Also see for CAFF60: Instruction manual

Contents

Caple CAFF60 Instruction Manual Manual pdf 19 page image

Instruction manual CAFF60 Instruction manual CAFF6036 37Please keep this instruction manual for future reference Please keep this instruction manual for future referenceI M P O R TA N T N OT E :It is strongly suggested that the refrigerator should be tilted to its left side (freezer side) whilecarrying but only if necessary.If for any reason the unit has to be tilted the unit must stand upright for a minimum of 24 hoursbefore connecting to power.I M P O R TA N T N OT E :Due to the refrigerator being heavy a caution should be taken to ensure the unit is moved andplaced with adequate human power.P O S I T I O N T H E U N I TPlease make sure all electrical and plumbing requirements are done, before placing the unit.I M P O R TA N T N OT E :Make sure the rear levellers are in their lowest position while setting the refrigerator in its place.Levelling should not be completed until the unit is in the desired position.L E V E L L I N G T H E U N I TAfter positioning has been done, levelling should be done for proper placing. When the unit isproperly levelled, door and drawer adjustments are less likely to be changed from the factorydefault settings.Firstly rear adjustment should be done with using a 13mm socket wrench. Turn the bolt clockwiseto raise the unit or counter clockwise to lower it. Refer to the picture below for the position of therear roller base adjustment.I M P O R TA N T N OT E :The floor can be reference for levelling, and not surrounding cabinetry. This could have influenceon the operation of the unit, such as door closing or drawer closing.The front levelling legs could be adjusted by turning them counter clockwise.down the refrigerator to floor with applying force only sides of it.rtant note: Please do not use the middle bottom part of the refrigerator forng.rtant note: It is strongly suggested that the refrigerator should be laid to itside(freezer side) while carrying.any reason the unit has been laid on other than the left side, the unit mustupright for a minimum of 24 hours before connecting to power.o the refrigerator being hefty a caution should be taken to sure that the unit isd and placed with adequate human power.Position the Unite make sure all electrical and plumbing requirements are done, before placingnit.ion: Do not tilt the refrigerator in any direction. This action can cause malfunc-50 has own rollers, so it can be moved easier than moving on pallet.rtant note: Make sure the rear levellers are in their lowest position whileg the refrigerator to its place. Levelling should not be completed until the unitesired position.Levelling the Unitpositioning has been done, levelling should be done for proper placing. Whennit is properly levelled, door and drawer adjustments are less likely to beged from the factory default settings.The front levelling legs could be adjusted by turning them counter clockwise.Warning: To avoid of the unit tipping forward, the front levelling legs should touchthe floor.All cWar2.6.L tybly a• Pla• Th• L tloca• Ma• Mathe• FaOptional AccessoriesPanelseestanding installations, stainless steel side panels are available through yourrized dealer.panels are installed using special screws and shims supplied with the sidels. First lift the side panel up a little. Push and align side panel to the side of the2.12 Water Filtration SystemWater Filter Bypass ModeWater filter is taped at the back of the top cover. After installation is completed,please insert the cartridge to filter housing then turn it to clockwise.If water filtration in not necessary, the water filter cartridge can be removedor not be installed in the first place. Thus the system can be operated inREAR ADJUSTMENTFRONT LEVELLING LEG2.1SopmaldatafindTheW A R N I N G :To avoid the unit tipping forward, the front levelling legs should touch the floor.A N T I - T I P B R A C K E T I N S T A L L A T I O NFor safety precautions it is important to fix the system to the surrounding to prevent tippingover. There are two different methods which can be applied for free-standing type and built-in type. The content of fixating elements in the anti-tip package includes for two types ofinstallation.Content of Anti-tip package;» Fixing Pin - 4 pieces» 2mm String - 8 pieces» Lag Screw (D4X20) - 4 pieces» L type Bracket - 2 pieces» Screw (M5X16) - 2 pieces» Plastic Wall Plug - 4 pieces» Lag Screw (D4X35) - 4 piecesAll components will not be necessary for each installation.