Canon ZDJ-S01 Operation Manual

Canon ZDJ-S01 Operation Manual Manual pdf 1 page image

2 MOUNTING AND CONNECTING2-1. Mounting the Zoom DemandMount the zoom demand onto the pan handle of the tripod by one of the two procedures below.A. For a demand that is put onto the pan handlePut the sleeve onto the pan handle of thetripod until it stops, then turn the lock lever tosecure the sleeve.The applicable pan handle is φ 28.25-28.45mm in diameter.B. For a clamper(CR-30)-mounted demand1. Loosen the large and small fasteningknobs of the clamper, then mount the clamper to the panhandle of the tripod.2. After mounting the clamper to the pan handle of thetripod, tighten the large and small fastening knobs of theclamper to secure the clamper.3. Mate the rose joint of the zoom demand with the rosejoint of the clamper.4. Tighten the mounting knob of the clamper firmly to fix theclamper to the zoom demand.NOTE1. The mounting angle of the zoom demand can beadjusted according to how the rose joints are mated.2. This zoom demand has three rose joints. Mount thezoom demand using the rose joint at the desirableposition for easy operation.2-2. Connecting the Demand CableFollow the procedures below to connect the demand cable to the lens.1. Plug the male connector of the demand cable into the receptacle labeled “TO SERVOCONTROL” at the rear bottom of the lens, then turn the fixing ring of the connectorclockwise to tighten the demand cable securely.2. Plug the other end of the cable into the connector on the zoom demand.SleeveLock Leverφ28.25-28.45Pan HandleClamper(cylinder type)LockLockFastening KnobClamper(CR-30)Pan HandleZoom DemandClamper(CR-30)MountingKnobRose Joint1/2© 2022.10 CANON INC.BT1-D018-A-ENG[External view]66.676.5View B(ENG/PD)2961 3.8 3.744.5ViewＡ1254.5A6290°160φ40168.1Tracking Switch(MEMO/OFF/ON)139.4Bφ40(Unit : mm)MEMO Switchφ28.25-28.45View CCRose JointExtender Selector SwitchTorque Adjusting KnobTalk-Back SwitchIS Switch(Lights green when IS is on）Connector to LensGripFrame Preset SwitchThumb RingRose Joint(A/S/B)Zoom Output Curve Selector SwitchMaximum Zoom Speed Adjusting Knob90°RET1 SwitchRET2 SwitchMake sure all of the following items are included in the packing box. If you find any itemmissing, please contact your dealer.・Zoom Demand・Clamper（cylinder type）・Demand Cable・Operation Manual "Before Using The Product"・Operation Manual "Regulations"1 PRODUCT LIST3 OPERATION AND FUNCTION3-1. Zoom OperationThe lens is zoomed toward the telephoto end by turning the thumbring of the zoom demand clockwise, as viewed from the grip of thedemand.The lens is zoomed toward the wide-angle end by turning thethumb ring counterclockwise.The zoom speed varies according to the rotation angle of thethumb ring.During zooming, the approximate focal length can be checkedwith the indicator on the left side of the lens, as viewed from thecamera.3-2. Maximum Zoom Speed AdjustmentThe maximum zoom speed obtained by completely turning the thumb ring of the zoom demand canbe changed with the maximum zoom speed adjusting knob.Turn it clockwise to increase the zoom speed. And, turn it counterclockwise to decrease the speed.3-3. Torque AdjustmentTurning the torque adjusting knob on the zoom demand clockwise to increase the torque for thethumb ring rotation.To decrease the torque, turn the knob counterclockwise.3-4. Selecting the Zoom Output CurveZoom speed characteristic curve (zoom output curve) with respectto the rotation angle of thumb ring is selectable among three kinds.Use the zoom output curve selector switch “Curve” for selecting azoom output curve.3-5. Talk Back (Microphone) OperationWhen the camera has a talk back function, the talk back switch onthe top of the zoom demand can be used.When it is pushed to “ENG” side, it is locked and a cameramancan talk with an engineering staff. So long as it is pushed to “PD”side, a cameraman can talk with a producer.3-6. Return OperationThere are two RET switches (RET1, RET2) on the grip of the zoom demand.While the RET switch is held down, on air picture/being recorded picture can be seen in theviewfinder through camera control system when multi cameras are connected to its system.3-7. Extender Selector SwitchOperate the extender by switching the extender selector switch on the zoom demand.“ON” side : Extender function is enabled“OFF” side : Extender function is cancelled(1x)Lens Demand CableZoom DemandTO SERVO CONTROL .LockFixing RingThumb Ring0← Rotation angle of thumb ring →ASBOutput Curve← 0 Zoom Speed → MAXBefore using the product, make sure to read the "GENERAL SAFETY INFORMATION"and be sure to use the product correctly.Thank you for purchasing a zoom demand ZDJ-S01. This zoom demand ZDJ-S01 is anaccessory used to perform zoom servo operations of a box type lens. The zoom can beoperated remotely by using this demand.This product comes with the following documents:• Operation Manual "Before Using The Product" （Included with the product）• Operation Manual "Regulations" （Included with the product）• Operation Manual （Web）Lens AccessoryZoom DemandZDJ-S01OPERATION MANUAL

/ 2

Related manuals for Canon ZDJ-S01