OneStart

Menu

Canoga Perkins 6002 User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Figure 1. Model 6002 and 6004 Rack Mount Modules
  4. Figure 2. Model 6000 Series of Devices Stand Alone Module
  5. unpacking and installing the stand alone models
  6. fiber optic cabling
  7. checking optical power levels
  8. measuring receiver input power
  9. Figure 4. WWDM Installation Diagram
  10. Figure 5. Model 6000 Stand Alone (Front View)
  11. Figure 7. Rack Mount Module Components
  12. Figure 8. EdgeAccess UCS DMM Main Menu Screens
  13. Figure 9. Chassis Management Screen Showing Inserted Modules
  14. Figure 11. Accessing the Select Module Menu
  15. Figure 12. Entering a Descriptive Name for the 6002 Module
  16. Table 1. Troubleshooting Cause and Solution Chart
  17. specifications
  18. Table 2. Unidirectional Two Channel WDM Chart
  19. Table 3. Unidirectional Three Channel WWDM Chart
  20. A.1 Warranty
  21. A.1.3 Limitations
  22. A.4 Extended Warranty Policy
Canoga Perkins 6002 User Manual Manual pdf 14 page image
EdgeAccess® Universal Chassis System6002/6003/6004 WWDM Users Manual3-23.2 Operation of the Stand Alone ModelsTo ensure proper optical performance levels, you will need to determine the loss budget. Thisfactor will ensure link integrity and ample signal strength at the remote end of your link.To operate the 6002 stand alone model:Step 1 Measure each of the optical composite fiber links at the lowest wavelength of operation.This will determine the limiting factor in the loss budget. Each Tx device attached to theWDM (Wavelength Division Multiplexer) has a loss budget that was specified by themanufacturer. This specified loss budget must be greater than the measured loss of thefiber link, plus the additional attenuation of the WDM. For applicable channel andwavelength specifications, see the tables in Chapter 6.Example for a Model 6002, 1310/1550 WWDM:The composite link has an 8dB loss measured at 1310nm. The device attached to the1310nm channel has a stated loss budget of 15dB. The 6002 1310/1550nm model has amaximum end-to-end attenuation of 2dB for a pair of units on SMF (single mode fiber).Factor in approximately 1dB for the additional connector loss from the patch cablesbetween the 6002 and the local devices. This would result in a safety margin ofapproximately 15dB – (8dB + 2dB + 1dB) = 4dB.Note: When connecting any device, pay attention to the proper wavelength channel.Step 2 Attach one (1) composite fiber link cable to the connector marked "Remote Tx" on thelocal WDM and "Remote Rx" on the remote WDM. Refer to the WWDM InstallationDiagram in Figure 4 for connection orientation.Step 3 Check the installation. The equipment is now ready to transmit the optically multiplexedsignals. Figures 5 and 6 represent the non-powered 6002/3/4 stand alone models.Figure 5. Model 6000 Stand Alone (Front View)Figure 6. Model 6002 Stand Alone (Rear View)
/ 29
Related manuals for Canoga Perkins 6002
Canoga Perkins 3240S User Manual first page preview
Canoga Perkins 3240S User Manual
This manual is suitable for:
600260036004
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved