Menu
Cannondale 2012 IQ300 Setup And Owners Manual
      |
THANK YOU FOR PURCHASING A CANNONDALECongratulations on your purchase of a Cannondale IQ Series computer.Proper setup and operation will greatly enhance this product’s usefulness and yourenjoyment.Please follow all Warnings and read all sections of this manual carefully and become fullyfamiliar with its operation before using it.YOUR CANNONDALE RETAILERAlong with this manual, your key source of information and assistance is the shop whereyou purchased this product. Your local Authorized Cannondale Retailer is your primarycontact to discuss service and adjustment to this product, instruction in its use, and anywarranty questions.To find an Authorized Cannondale Retailer closest to you, call 1-800-bIke-uSA. Or you canuse our dealer locator at our website www.cannondale.com.IMPORTANT INFORMATION FOR ALL CANNONDALE CYCLING COMPUTERSWARNINGSWIRELESS COMPUTER MODELS (IQ200, IQ300, and IQ400) - People with medical/implanted electronic equipment or devices such as heart pacemakers, ekG equipment,etc. must not use wireless cycle computers due to possible risk of interference with themedical devices.EXERCISE - Adults with health problems (such as heart disease, diabetes or obesity) orthose at high risk, men over age 40 and women over age 50 or pregnant should talkwith their doctor before starting an exercise program.INTENDED USE: For bicycle use only. Not for use on any motorized vehicle.OPERATE COMPUTER ONLY WHEN NOT RIDING: Failure to pay attention to the road,trail, traffic or your surroundings could result in an accident, with risk of serious injury,paralysis or death. You must focus on riding, not your computer. Learn computer opera-tions, and do all possible computer operations when not riding. For any operations youchoose to perform while riding, choose a time and place where this distraction has lessrisk.MAKE SURE ALL COMPUTER PARTS ARE INSTALLED PROPERLY: The computermust not interfere with the bicycle controls and your ability to use them. Mount thecomputer according to the directions in this instruction manual. See your AuthorizedCannondale Retailer if you have any trouble installing or maintaining your computer.CHECK FOR DAMAGE REGULARLY: Regularly check the position, alignment, andcondition of the spoke magnet, wireless sensor, cadence sensor, sensor and sensor wireto make sure they are secure, aligned and in good condition. Make sure nothing is looseand there are no worn or damaged parts.BATTERIES: use only battery size and type specified on the unit. Do not leave anybatteries in reach of children, and dispose of them correctly. If a battery is swallowed,consult a doctor immediately.NOT A TOY: keep this computer and associated parts including the battery away fromchildren. Small parts could be swallowed.YOU CAN BE SEVERELY INJURED, PARALYZED OR KILLED IN AN ACCIDENT IF YOUIGNORE THESE WARNINGS.NOTICE■ This product is rain-proof only. Do not submerge or power wash.■ Do not disassemble the unit.■ Mount the computer according to the directions in this instruction manual.■ Avoid direct impact to the computer unit.■ Avoid using the computer unit in or near strong electromagnetic fields such ashigh-voltage power lines or other transmitters.■ Clean the unit with a mild detergent and a soft dry cloth. Never use any kind ofsolvent or alcohol.■ To prevent damage caused by battery leakage, remove the batteries before storageor long period of non-use. Do not reverse battery installation. Observe positive (+)and negative (-) markings.■ WIReLeSS MODeLS (IQ200,IQ300, IQ400) Wireless computer uses an analogwireless signal. It is not digitally coded but uses technology to lower the chance ofinterference with circuitry used in other electronic devices such as lights, phones ,computers, etc.2012 IQ300 ComputerSetup and Owners Manual - 11/11COMPUTER PARTSCOMPUTER INSTALLATIONThe computer unit can be mounted on a bicycle handlebar or stem.1. To mount the bracket, insert two nylon ties through the mounting bracket slots.(a) - handlebar slots, (b) stem slots2. Insert the rubber pad into back of mount bracket for handlebar or stem by aligningslots in the back of the mount with the pad.3. Position the pad/bracket onto the handlebar or stem and tighten both nylon tiessecurely. Carefully snip tie ends 1-2mm from tie head.To mount the computer onto the bracket, position it into the bracket at a 45 degree angle,hold down and rotate the computer unit clockwise to lock it in place. To remove it, rotatethe computer counter-clockwise and lift it off.NYLON TIESMOUNTING BRACKETHANDLEBARa btouchtouchSENSOR INSTALLATIONCheck the following components before installation:1. Position the sensor on the front of the right fork leg within 60 cm of the computer. Thebattery door must face out with the tear drop shape pointing down shown.2. Pass the two cable ties through the sensor mounting holes and loosely mount the forksensor body to the left fork blade (do not fully tighten the cable ties at this point).Loosely install the sensor magnet to one of the spokes of the front wheel. Adjust theposition of the magnet and sensor together so that the magnet is aligned with the line onthe bottom edge of the sensor and 1-2 mm separates the two parts and tighten both partsin place.Secure the sensor to the fork leg with two nylon ties.3. Install the magnet onto a spoke so the magnet will pass over the sensor in the pickup zonewhen the wheel is rotated.4. Set the sensor-to-magnet gap by tilting the sensor toward or away from pickup zone. Themaximum distance between the speed sensor and magnet on the spoke is 5 mm.5. When set, draw the nylon ties securely. Carefully snip the tie ends 1-2mm from tie head.IQ300 COMPUTER UNIT(back)(front)WIRELESS SENSORSPOKE MAGNETNYLON TIES (X4)MOUNTING PADMOUNTING BRACKET(back)(front)touchMAX. 30 oMAX.60 cm5 mmMAX.5 mmSPOKEMAGNETPICK-UP ZONEWIRELESS SENSORSENSORPROGRAMMING BUTTONSENSORINDICATOR LED |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved