Calpeda Easymat Operating Instructions Manual

Calpeda Easymat Operating Instructions Manual Manual pdf 3 page image

GBBS...IMAT Rev2 - Operating Instructions Page 3 / 121.2. Manufacturer name and addressManufacturer’s name: Calpeda LtdAddress: 6-8 Wedgwood Rd Ind EstBicester OX26 4UL, UKwww.calpeda.co.uk1.3. Authorized operatorsThe product is for qualified operators upon finalusers and specialized technicians. (see above).i It’s forbidden for the final user to do anyoperation reserved only for the authorizedtechnicians. The manufacturer isn’tresponsible for the related damage done bymissing this prohibition.1.4. WarrantyWarranty covers all defects within the booster setresulting from faulty workmanship and/or materialsfor a period of two years from the date of installationor 30 months from the date of dispatch from ourproduction centre, whichever is the shorter.i The warranty covers the replacement orrepair of the faulty parts and labour to do so.It does not cover any secondary loss, costsassociated with the removal, returning orrefitting of the set.Under no circumstances should the faultyequipment be dismantled. Failure to comply couldinvalidate the warranty.The warranty may be lost in these cases:- Whenever the use of this product is different fromits intended use described in this manual.- Defects arising from incorrect installation and/oroperation.- In case of modifications or customizations madewithout the authorization of the manufacturer.- In case of technical assistance operations madeby non-authorized personnel.- In case of missing maintenance (described in thismanual).1.5. Technical assistanceAny further information on documents, serviceassistance, and device parts, please contact:Calpeda Ltd6-8 Wedgwood Rd Ind Est,Bicester OX26 4UL, UKT:+44 1869 241441 F: +44 1869 240681E: pumps@calpeda.co.ukW: www.calpeda.co.uk2. TECHNICAL DESCRIPTIONConstant pressure booster sets with built-infrequency converter made with multiple pumps,ball valve, non-return valve and pressure gauge ondischarge side, ball valve on suction side.EASYMAT – Domestic and Commercial useI-MAT – Domestic, commercial and industrial2.1. Intended useFor clean liquids: non-explosive and non-flammable,non-hazardous for health or the environment, nonaggressive for booster set materials, not containingabrasives, solid or fibrous particles.Liquid temperature from 0 °C to + 40 °C in line withthe regulation.2.2. Expected improper useThe device is designed and manufacturedexclusively for the purpose described in sec. 2.1.Improper use of the device is forbidden, asis use under conditions other than thoseindicated in these instructions.Booster sets must not be used in hazardousareas as they could cause an explosion ifthere is the danger of ignition by a flamepath.It will be not accepted liability for the use of oursets with liquids which could be construed as beinghazardous to health either by touch, ingestion, orinhalation of fumes or gases given off by the liquid.Calpeda cannot be held responsible for failuresor injuries related to the inobservance of therestrictions described.2.3. MarkingThe following picture is a copy of the name-plate.1) Type2) Working pressure3) Total power4) Control panel5) Weight6) Certifications7) Serial number3. TECHNICAL CHARACTERISTICSDimensions and weight (see technical catalogue).Protection IP54 (depending on pump model)Supply voltage / Frequency:EASYMAT 230 V1~50 HzI-MAT 400V3~50 HzSound pressure: refer to individual pump dataMaximum permissible pressure: up to 10 bardepending on model.3.1. Operating conditionsThe product works properly only if the followingsconditions are respected.Floating voltage rate: +/-10% maxFloating frequency rate: +/- 4% maxAmbient temperature: up to 40°CRelative Humidity: up to 90% without condensingAltitude: Below 1000 m inside a building.i Booster sets must be used in conjunctionwith a cold water storage tank and must notbe connected direct to mains in-line withwater byelaw regulations.3.2. Product overviewThe booster set is generally made of: