Menu
CAMDEN CV-7600C Installation Instructions Manual
Also see for CV-7600 Series: Installation instructions
     |
Page 1 of 5Access Control and Telephone Entry1. GENERAL DESCRIPTIONA key component of a physical security electronic access controlsystem, a mobile-ready reader combining BLE and contactlesssmart card technologies is based on RFID technology.In operation it is capable of reading data stored on a contactlesssmartcard credential via high frequency—or reading data frommobile credential stored in a smartphone’s wallet app via BLEtechnology—and without physical contact, and then passingthe data obtained to the physical access control system.Access control systems typically manage and record the movementof individuals through a protected area, such as a locked door.CV-7600 Series-BLEBluetooth Card ReaderINSTALLATION INSTRUCTIONS2- #6 x 1" Self-Tapping Screws2- 6-32 x 1" Pan Head Phillips Screws1- Single Gang Mounting PlateTHIS PACKAGE INCLUDES:3. SPECIFICATIONS (WITH CARD READER DRAWING)Input Voltage 8 to 14 VDCCurrent Draw 40 mA typical @ 12VDC 195 mA peakFrequency 13.56 MHz (contactless smartcard) 2.4 GHz (BLE)Cabling 24 AWG minimum, multi-conductor strandedwith foil shieldInterface Wiegand (26-bit formats), ABA Track IImagnetic strike (clock & data) or OSDPOperatingTemperature -40°F to 149°F (-40°C to 65°C)LED Control Blue, Red, Green, Amber and OffRead RangePhysical: Up to 1.5" (38mm)Mobile: CV-7600: Up to 1 ft (30 cm)CV-7615: Up to 15 ft (4.6 m)Audio Tone Beeper included standardProtection IP67DimensionsMullion: 1 3/4"W x 11/16"H x 1 13/16"D(44mm x 119mm x 30mm)Switch Plate: 3"W x 5 1/8"H x 1 3/16"D(76mm x 130mm x 30mm)Notes:1. Optimized for use with devices supporting BLE version 4.2.2. Carrying the ETL Label and tested by Intertek, conforms toUL Standard 294.3. Self evaluated.4. Linear power supplies are recommended for best operation.5. Using CV-MCS Clamshell Contactless Smartcard with 12 VDC atthe reader (other credentials may be less). Read ranges subjectto the smartphone used, the manner in which used, as well asthe installation and it's environment.6. Ex. Belden 9535 or similar, supporting the five conductorscomprising the physical layer of the Wiegand interface (power,ground, data 0, data 1, and/or beeper and LED). Alternatively,Belden 9539 or similar, for all reader functions. Contact youraccess control system manufacturer for specific requirements.7. CSN = Card Serial Number1- 6-32 x 1/4" Pan Head Phillips Screw1- 6-32 x 1/4" Tamper-Resistant Button Head Hex Drive Screw2. CONEKT WALLET APPInstructions:1) Using the target smartphone, download and install theConekt Wallet App. The App can be found on the Apple Store orGoogle Play Store or by the following link:http://onelink.to/sb6srb2) Once installed, launch the Conekt Wallet App, then select the"+" button to load a new Conekt Mobile Access Credential.3) When prompted, enter the 16- character Conekt RegistrationKey. This will download and activate the Conekt MobileCredential. The Conekt Registration Key may be manuallyentered or, using the associated QR code, scanned with thesmartphone's camera.4) The Conekt Mobile Access Credential will now appear in theConekt Wallet App, ready to use. |
Related manuals for CAMDEN CV-7600 Series
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved