AutoDome Modular Camera SystemVG4 Series Firmware Update Manualen Firmware Update Manual

VG4 Firmware Update via a TCP/IP Network

Navigate to the Firmware Update Page

Upload the Firmware Files

Selecting the Files

VG4 Firmware Updates via the CTFID

Bilinx Connections

Launching with a Bilinx Connection

Update the VG4 AutoDome Firmware

Minimum Requirements

Troubleshooting

IP Firmware Update Error

BILINX

Bosch VG4 Series Manual

Safety

Safety Precautions

Customer Support and Service

Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts

Description

Mount Power Supply Box

Route Wires and Attach Connectors

Power Supply Box Connections

Route Power through Intermediate Power Supply Box

Attach Pendant Arm to Power Supply Box

Make Connections in Power Supply Box

Installing the VG4-A-ARMPLATE

Attach the Pendant Arm to the Mounting Plate

Route and Connect Wires to a Power Supply Box

Assemble Pendant in Packing Box

Attach Pendant to Arm and Tighten

Installing the Pressurized Environmental Housing

VG4 Pressurized Environmental Mounting Options

Required Equipment

Attaching the Housing to the Arm

Calibrating the Pressure Sensor

Attaching the Bubble to the Housing

Pressurizing the Housing

Installing Roof Parapet and Pipe Mounts

Tools Required

Attach Cover Door

Wiring the Power Supply Box

Installing the VG4-A-9230 Roof Parapet Mount

Installing the VG4-A-9543 Pipe Mount

Wire the Pipe Interface Board

Wiring for Multiple AutoDomes

Assemble the Pendant in Packing Box

Attach Pendant to Pipe and Tighten

Make Connections in the Power Supply Box

Important Installation Safeguards

Attaching the Housing to the Pipe

Servicing the Pressurized Environmental Housing installation

Installing the In-Ceiling Mount

Pre-installation Check List

Prepare Drywall Ceiling for Installation

Wire the Interface Box

Interface Box Connections

Attach Housing to the Interface Box

Secure Housing to Ceiling

Align and Install Camera Module

Cable and Wire Standards

Video and Control Cables

Control-only Cables

Fiber Optic Module with an RS232/RS422 Controller

Audio Cables

Alarms and Relay Connections

Configuring a Normally Closed Supervised Alarm

Configuring a Normally Closed Non-supervised Alarm

Bubble Handling and Cleaning

A Installation Notes for AutoTracker

A.2 Mount/Mounting Surfaces

Index

VG4 Series

VG4 Firmware Updates via a TCP/IP Network

Upgrading the IP AutoDome

Upgrading the VG4 100 Series AutoDome

Selecting the Service Pack

Beginning the Firmware Update Process

Updating VG4 100 Series IP AutoDome Firmware

Updating VG4 200, 300 or 500i Series IP AutoDome Firmware

Selecting and Uploading Firmware Files

Alternate Language Option

Changing the VG4 AutoDome OSD Language

Upgrading the VG4 200 or 300 Series AutoDome

Hardware Connections

Launching the CTFID Software

Launching with a RS232/RS485 Serial Connection

Uploading VG4 AutoDome Firmware Files

Uploading a VG4 200 or VG4 300 Series AutoDome Service Pack

Order to Upload Files

Updating the SC Boot file

Updating the SC Main Files

Additional Language Option

VG4 AutoDome with an IP Communications Module

Upgrading Firmware with the CTFID

Auto Tracker Does not Activate with ON 78 ENTER

AUTODOME Bubble Replacement

Parts List

Cleaning the Bubble Exterior

Replacing an AUTODOME Bubble

Replacing an In-ceiling Rugged Polycarbonate Bubble

Replacing an In-ceiling Acrylic Bubble

Replacing an In-ceiling HD Acrylic Bubble

Replacing a Pendant Bubble

About VG4 AutoDome Firmware Updates

Updating the SC Main files

Prepare Suspension Ceiling for Installation

Configuring the VG4 AutoDome

Configuring a Normally Open Non-supervised Alarm

Alarm Outputs

customer support and service

important safeguards

safety precautions

Pre-installation Checklist

power supply box connections

attach cover door

wiring the power supply box

Wire Pipe Interface Board

interface box connections

Attach Bubble

Configuring Non-supervised Alarms (inputs 1 through 7)

Glossary

Bosch VG4 Series Manual

Product

Learn More

Legal


Contents Table Of Contents VG4 Firmware Update via a TCP/IP Network Navigate to the Firmware Update Page Upload the Firmware Files Selecting the Files VG4 Firmware Updates via the CTFID Bilinx Connections Launching with a Bilinx Connection Update the VG4 AutoDome Firmware Minimum Requirements Troubleshooting IP Firmware Update Error BILINX	AutoDome Modular Camera SystemVG4 Series Firmware Update Manualen Firmware Update Manual Next / 26