Bosch B925F Installation Manual

Also see for B925F: User quick reference guide Installation guide

3 | Installation2.1 | Access the address switches1 | OverviewCaution!Remove all power (AC and battery) before making anyconnections. Failure to do so might result in personalinjury and/or equipment damage.5 | Status indicatorsStatusindicatorFunctionReady to turn on (arm)Turned on (armed)GAS Gas alarmAC (Mains) power presentFire keypadindicatorFunctionFire alarmSilencedSupervisory conditionSystem troubleAdjusting nightlight (for control panels with version 2.01 orhigher):1. Press [MENU] or press [CMD][8] to open the Main menu.2. Use [NEXT] to go to the Press 5 for Settings Menu option,or simply press [5].3. Use [NEXT] to go to the Press 4 for Keypad Config option,or simply press [4].4. Use [NEXT] to go to the Press 4 for Nightlight option, orsimply press [4].5. Use [PREV] or [NEXT] to toggle between the Yes and Nooptions.6. Press [ENTER] while viewing the desired option to save theprogramming.7. Press [ESC] to exit the menu.Adjusting the brightness:1. Press [MENU] or press [CMD][8] to open the Main menu.2. Use [NEXT] to go to the Press 5 for Settings Menu option,or simply press [5].3. Use [NEXT] to go to the Press 4 for Keypad Config option,or simply press [4].4. Press [1] to adjust the brightness.5. Use [PREV] or [NEXT] to adjust the brightness level. Thechanges apply immediately.6. Press [ESC] to exit the menu.4 | Display3.1 | Install the keypad3.2 | Attaching to the control panelYou can surface install the keypad, or install it to standardelectrical boxes, including single gang boxes.1. Use the base as a template to mark surface.2. Pull the wiring through the opening in the base.3. Use the mounting hardware to attach.Use the control panel terminals labeled R, Y, G, B (PWR, A, B,COM). Connect them to the keypad terminals labeled R, Y, G, B.Keypads can be wired directly to the control panel or fromkeypad to keypad.Callout ― Description1 ― Control panel2 ― Terminal wiring3 ― Keypad’s wiring terminal block1 23RYGBSDI2PWR+/RA/YB/GCOM/B27282926eSDI2PWR+/RA/YB/GCOM/B28293027eReconnect the keypad to the base by sliding the keypad ontothe base (reverse of Step 2). Apply power to the system.SDI2PWR+/RA/YB/GCOM/B27282926eSDI2PWR+/RA/YB/GCOM/B28293027eRYGB2 | SDI2 address switchesTwo switches set the address for the keypad. The control paneluses the address for communication.GASGASSet the address switches per the control panel configuration.Each SDI2 keypad must have a unique address. For single-digit addresses 1 through 9, set the tens switch to 0. Thefollowing illustration shows the address switch setting foraddress 1.Callout ― Description1 ― Address switches12.2 | Setting the address switches1. Use a slotted screwdriver. Turn the lock counter-clockwise.2. Push down on the keypad to remove it from the base.3. Find the switches on the back of the keypad.Refer to the following illustrations.12This keypad is an SDI2 bus compatibleCallout ― Description1 ― Wall mount holes2 ― Single gang box holes3 ― Double gang box holes4 ― Wire opening5 ― Surface mount wire openings6 ― Gang box holes (3-4 in)7 ― Surface mount wire channel8 ― Bubble level9 ― SDI2 wiring terminal block10 ― Wire tie postsR Y G B6 2491 2337 7 551 1106 6 581010

/ 2

Related manuals for Bosch B925F