Menu
Black & Decker WPS100 Instruction Manual
  |
IMPORTANT SAFETY INSTRUCTIONSWARNING: TO REDUCE THE RISK OF INJURY, USER MUST READ ANDUNDERSTAND INSTRUCTION MANUAL.1. Do not use or mount power tools on top surface.2. Do not load top surface with more than 50 lbs (23 kg).3. Do not apply an unbalanced or overhanging load to top surface which could cause a tip-over.4. Do not sit, step, or stand on Paint Station. Do not use as a stepladder or standing platform.5. Do not use on an uneven or unstable surface.6. Do not store flammable materials.7. For indoor use only. Do not store Paint Station outdoors or in a damp location.8. Be sure that the legs are fully open and that the locking arms are secured in the moldedleg slots as shown in Figures 2 and 3.9. If product is dropped and damaged, take to an authorized servicer. See “ServiceInformation”.10. If using any chemicals other than latex paint and soap and water solutions, make sure that thechemical is suitable for use with plastics.11. Follow all warnings, usage and disposal instructions as recommended by the manufacturer ofany chemical used with this productVEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.INSTRUCTION MANUALCat No. WPS100 Form # 628716-00 (NOV-04)Copyright © 2004 Black & Decker Printed in ChinaBEFORE RETURNING THIS PRODUCTFOR ANY REASON PLEASE CALL1-800-544-6986IF YOU SHOULD HAVE A QUESTION OR EXPERIENCE APROBLEM WITH YOUR BLACK & DECKER PRODUCT,CALL 1-800-544-6986BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., ANDDATE CODE (e.g. 20000130M). IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVEYOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.YOUR FEEDBACK IS VITAL TO BLACK & DECKER.Catalog No. WPS100Portable Paint StationTrash BagHolderTape HolderCarry HandleSwitch plate, outletcover, etc. storage Wet brush saddle restRemoveable rollertray with sealablecoverTool StoragePaint can retainer-Gallon,quart,pintTray retentionknobs clips fortransportPaper towelroll holderFeatures1SAVE THESE INSTRUCTIONS FOR FUTURE USE.UNPACKINGRemove the folded Paint Station from the carton and follow the steps below to set up theunit.CAUTION: Avoid pinch points when opening legs as shown in Figure 1.UNFOLDING:1). With the Paint Station resting on its side, grasp the end of the leg and pull it outward to itsfull open position.2.) Grasp the spring loaded locking arm and engage it in the slot as shown in Figure 2.WARNING: Make sure that arm is completely seated in both slots by pushing arm downon both sides.3.) Grasp the end of the other leg and pull it outward to its full open position. Grasp thespring loaded locking arm and engage it in the slot as shown in Figure 3. Make sure thatarm is completely seated in both slots by pushing arm down on both sides.4.) Place the Paint Station in an upright position.5.) Remove tape from tray lid.6.) Locate tray retention knobs (2) and insert into holes on table. See figure 4.USING THE PAINT STATIONNOTES:• To reduce the amount of clean up required, paint tray liners (not Included) can be used inthe roller tray. A 4 inch disposable tray liner can be used in the narrow cavity if using a 4 inchroller.• Wet paint rollers can be stored in the paint tray for approximately 24 hours without theneed to clean them. To store a wet paint roller, place lid on tray as shown in Figure 5 andsnap the lid in place.• A trash bag can be attached to the end of the Paint Station using the hangers shown inFigure 6. Secure with tape if desired.• A paper towel roll can be stored on the opening shown in figure 7. To attach the roll, firstpush the tube onto the upper post in the opening then push the bottom of the towel roll overthe lower post until the roll is secured.• Cleanup with mild soap and water if using latex paints. Make sure any solvents used for oilbased paint cleanup are suitable for use on plastics.FOLDING:NOTE: Remove paper towel roll and tape from storage positions on legs before folding.1.) Lock paint tray using tray retention knobs as shown in Figure 4.2.) Fold in leg farthest from the paint tray first by grasping locking arm and pulling out todisengage arm from slot.3.) Fold in remaining leg same as above. When leg is fully folded it will “snap” into place.TRANSPORTING PAINT STATIONTo move upright Paint Station from place to place, grasp the ends of the top as shown inFigure 8.To carry the Paint Station after it has been folded, use the upper or lower carry handlesshown in Figure 9. NOTE: It may be easier to transverse stairs if you carry unit by the lowerhandle, placing the upper part of the unit under your arm.STORAGE• Cleaned paint brushes and painting tools can be stored in the roller tray with the lidattached.• The Paint Station can be hung vertically using the triangular shaped hanging hole shownin Figure 10.SERVICE INFORMATIONBlack & Decker offers a full network of company-owned and Authorized Servicelocations throughout North America. All Black & Decker Service Centers are staffed withtrained personnel to provide customers with efficient and reliable power tool service.Whether you need technical advice, repair, or genuine factory replacement parts,contact the Black & Decker service location nearest you. To find your local servicelocation, refer to the yellow page directory under “Tools—Electric” or call:1-800-54-HOW-TO.FULL TWO-YEAR HOME USE WARRANTYBlack & Decker (U.S.) Inc. warrants this product for two years against any defects in materialor workmanship. The defective product will be replaced or repaired at no charge in either oftwo ways:The first, which will result in exchanges only, is to return the product to the retailer fromwhom it was purchased (provided that the store is a participating retailer). Returns should bemade within the time period of the retailer’s policy for exchanges (usually 30 to 90 days afterthe sale). Proof of purchase may be required. Please check with the retailer for their specificreturn policy regarding returns that are beyond the time set for exchanges.The second option is to take or send the product (prepaid) to a Black & Decker owned orauthorized Service Center for repair or replacement at our option.Proof of purchase may be required. Black & Decker owned and authorized servicecenters are listed under “Tools-Electric” in the yellow pages of the phone directory.This warranty does not apply to accessories. This warranty gives you specific legal rightsand you may have other rights which vary from state to state. Should you have anyquestions, contact the manager of your nearest Black & Decker Service Center.This product is not intended for commercial use.PATENTS PENDING.DIRECTIVES DE SÉCURITÉ IMPORTANTESAVERTISSEMENT : AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L’UTILISATEURDOIT LIRE ET COMPRENDRELE MODE D’EMPLOI.1Pinch PointZone de pincementPunto de pliegueSlotsFentesRanuras23SlotsFentesRanurasHoles for trayretentionknobs.Trous pourboutons deretenuedu bac.Orificios paralos sujetadoresde la bandejade pintura45 67 Upper postTigesupérieureSoportesuperiorLower postTigeinférieureSoporteinferior89 Upper carry handlePoignée de transportsupérieureAgarradera superiorpara trasladarLower carry handlePoignée de transportinférieureAgarradera inferiorpara trasladar10 Hang holeTrou desuspensionOrificiopara colgarSee ‘Tools-Electric’– Yellow Pages –for Service & SalesImported byBlack & Decker (U.S.) Inc.,701 E. Joppa Rd.Towson, MD 21286 U.S.A. |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved