Menu
Black & Decker Marksman BDSM400 Instruction Manual
       | |
Contents |
WARNING: Read and understand all instructions. Failure to follow all instructionslisted below may result in electric shock, fire and/or serious personal injury.SAVE THESE INSTRUCTIONSSafety InstructionsDANGER: Laser Radiation, avoid direct eye exposure, serious eye injury can result.• Do not use optical tools such as a telescope or transit to view the laserbeam.• Position the laser so unintentional eye contact will be avoided.• Do not operate the laser around children or allow children to operate thelaser.• Do not disassemble. Modifying the product in any way can increase the riskof laser radiation.WARNING: Use of controls or adjustments or performance of procedures other than thosespecified in this manual may result in hazardous laser radiation exposure.• Do not operate in explosive atmospheres, such as in the presence of flammable liquids,gases, or dust.• Use only with the specifically designated batteries. Use of any other batteries may create arisk of fire.• Store idle product out of reach of children and other untrained persons. Lasers aredangerous in the hands of untrained users.• Use only accessories that are recommended by the manufacturer for your model.Accessories that may be suitable for one laser, may create a risk of injury when used onanother laser.• Repairs and servicing MUST be performed by a qualified repair facility. Repairs performedby unqualified personnel could result in serious injury.• Do not remove or deface warning labels. Removing labels increases the risk of exposureto radiation.• For indoor use only.• This product is intended for use in a temperature range of 41°F(5°C) - 104°F(40°C).WARNING: Shock Hazard. Always turn off power when working near electrical wires.Drilling into or touching live wires can result in severe injury or death.CAUTION: Material thickness, type of material, moisture content, and other variablescan effect sensing results. The sensor may detect electric wiring or pipes in the samemanner that studs are detected depending on their location to the wall surface. Usecaution when drilling, nailing or cutting into walls, floors and ceilings which may containelectrical wiring or pipes. These items may be detected by the Stud Sensor in the samemanner in which studs are detected. Because studs are normally spaced 16 inches (406mm) or 24 inches (610 mm) apart and are usually 1-1/2 inches (38 mm) wide, beware ofanything closer together or of a different width.Liquid Crystal Display (First Aid Measures)• If liquid crystal comes in contact with your skin:Wash area off completely with plenty of water. Remove contaminated clothing.• If liquid crystal gets into your eye:Flush the affected eye with clean water and then seek medical attention.• If liquid crystal is swallowed:Flush your mouth thoroughly with water. Drink large quantities of water and inducevomiting. Then seek medical attention.Label SymbolsThe label on your tool may include the following symbols.V ..........................volts mW......................milliwattsnm ........................wavelength in nanometers IIIa ......................Class IIIa LaserInstalling the BatteryEnsure on/off switch (F) is in the full “OFF” position. Remove the battery compartmentcover (G) by pressing down on the center of the cover and pulling back. Insert a fresh 9 voltbattery making sure to match (+) and (-) terminals correctly. Replace the batterycompartment cover and securely snap into place.WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce thisrisk: • Carefully follow all instructions and warnings on the battery label and package.• Always insert battery correctly with regard to polarity (+ and -), marked onthe battery and the equipment.VEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.INSTRUCTIONMANUALCat No. BDSM400 Form # 624048-01 (SEPT-04) Copyright © 2004 Black & Decker Printed in ChinaBEFORE RETURNING THIS PRODUCTFOR ANY REASON PLEASE CALL1-800-54-HOW-TO (544-6986)IF YOU SHOULD EXPERIENCE A PROBLEMWITH YOUR BLACK & DECKER PRODUCT,CALL 1-800-54-HOW-TO (544-6986)BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., ANDDATE CODE (e.g. 20000130M). IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CANRESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVEUS A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.FEATURESB. Laser PointerC. LCD ScreenD. READ ButtonsE. Mode Detection SwitchF. On/Off SwitchG. Battery Compartment CoverCatalog No. BDSM4002 3A4 5 6KEYPAD DESCRIPTIONH.) SET - Select measurement referencefrom front or back of unit or at 90° to unitI.) FT/M - Select feet / inches or metricmeasuring unitJ.) RCL - Memory RecallK.) (X) - MultiplyL.) (+) - AddM.) (-) - SubtractN.) STORE - Memory InO.) (=) - SumBGH I JLKFEDCDMN7O9101118For your convenience and safety, thefollowing labels are on your product.Pour des raisons de commodités et desécurité, les étiquettes suivantes sontapposées sur ce produit.Para su conveniencia y seguridad, lassiguientes etiquetas están en su producto.12 |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved