Menu
Black & Decker Lights Out 90539953 Instruction Manual
     | |
Contents |
• Turns off the light if the room becomes brighter, for instance due to opening a windowshade. You can control the brightness setting for this feature.Selecting Where to Use the Auto SwitchThe Lights Out™ Auto Switch can be installed on toggle-style light switches, includingswitches that are part of a “ganged” multi-switch outlet.Use the Auto Switch in a location where the light switch has a clear view of room occupants,and where occupants are likely to be moving within range of the detector. Note that the AutoSwitch will turn the lights off if it does not detect motion within the selected time period. TheAuto Switch is especially useful in areas where a light is likely to be left on unnecessarily.Ideal locations are entry ways, bathrooms, garages, offices, basements and playrooms.The Auto Switch is not compatible with the following:• Paddle-style switches• Heavy-duty industrial-grade switches• Toggle switches with side-to-side motion, rather than up-and-down motion• “Three-way” switches (where the light is controlled by more than one switch)• Dimmer switchesAssembly/Set-upThis product requires three AA batteries (not included).Installing the BatteriesNOTE: Use only with the specifically designated batteries (AA non-rechargeable alkaline orlithium). Use of any other batteries may create a risk of fire.• Open the battery compartment cover (I) as shown in figure 1.• Insert batteries in the orientation indicated, making sure to match (+) and (-) terminals to theillustration inside the compartment, then close the battery compartment cover.Instructions for Mounting to a SwitchNOTE: Do not install where more than onelight switch controls a single light fixture (a“three-way” switch).• Note whether the light turns on when theswitch is flipped up, or when the switch is flippeddown. The Auto Switch can be configured foreither case.• Use a piece of tape (not included) to tape theswitch plate in place before the screws areremoved. See figure 2. You can skip this step ifthe switch plate is held to the wall with morethan two screws (for example, when there ismore than one switch.)• Remove the two screws from above andbelow the switch you want to control.• Orient the mounting plate as shown infigure 3, and line up the mounting plate holeswith the holes in the cover plate.• Using the two screws supplied, lightly screw inthe mounting plate (j) over the switch plate asshown in figure 3.• Tighten both screws until just snug. Do notover-tighten.SAFETY GUIDELINES - DEFINITIONSIt is important for you to read and understand this manual.The information it contains relates to protecting YOURSAFETY and PREVENTING PROBLEMS. The symbols below are used to help yourecognize this information.DANGER: Indicates an imminently hazardous situation which, if not avoided, will resultin death or serious injury.WARNING: Indicates a potentially hazardous situation which, if not avoided, couldresult in death or serious injury.CAUTION: Indicates a potentially hazardous situation which, if not avoided, may resultin minor or moderate injury.CAUTION: Used without the safety alert symbol indicates a potentially hazardoussituation which, if not avoided, may result in property damage.WARNING: To reduce risk of injury, user must read and understand instruction manual.WARNING: To reduce the risk of shock, remove this device and disconnect branch circuitwhen servicing switch or light fixture.WARNING: Do not use on a switch that controls a power receptacle.• Use with toggle-style switches only.• For indoor use only.• Not for use where the light fixture is controlled by more than one switch (a “three-way” switch).WARNING: Fire or burn hazard. Batteries can explode or leak, and can cause injuryor fire. To reduce this risk:• Carefully follow all instructions and warnings on the battery label and package.• Always insert batteries correctly with regard to polarity (+ and -), marked on the batteryand the equipment.• Do not short battery terminals.• Do not recharge.• Do not mix old and new batteries. Replace all of them at the same time with new batteriesof the same brand and type.• Remove dead batteries immediately and dispose of per local codes.• Do not dispose of batteries in fire.• Keep batteries out of reach of children.• Remove batteries if the device will not be used for several months."Transporting batteries can possibly cause fires if the battery terminals inadvertentlycome in contact with conductive materials such as keys, coins, hand tools and the like.The US Department of Transportation Hazardous Material Regulations (HMR) prohibitstransporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryonluggage) UNLESS they are properly protected from short circuits. So when transportingindividual batteries, make sure that the battery terminals are protected and well insulat-ed from materials that could contact them and cause a short circuit.SAVE THESE INSTRUCTIONSIntroductionThe Lights Out™ Auto Switch will reduce your electricity usage and save you money byturning off a light when it is not needed. It uses motion and light detectors to automaticallycontrol an existing toggle-style light switch.The Auto Switch performs these functions:• Turns on the light when motion is detected.• Turns off the light when no motion has been detected for a selectable time period.• Does not turn on lights if the room is already illuminated with sunlight. You can control thebrightness setting for this feature.Cat No. SW100 Form # 90539953 (OCT.’08)Copyright © 2008 Black & Decker Printed in ChinaFEATURESA.) Motion DetectorB.) Motion Detector ShadeC.) Manual On/Off SwitchD.) Timer SwitchE.) Ambient Light SwitchF.) Power SwitchG.) Polarity SwitchH.) Battery CompartmentI.) Battery Compartment CoverJ.) Mounting PlateVEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.Catalog NumberSW100Lights Out™ Auto Switch13ACDEHIFGJB2TapeRuban adhesifCintaThank you for choosing Black & Decker!Go to www.BlackandDecker.com/NewOwnerto register your new product.PPLLEEAASSEE RREEAADD BBEEFFOORREE RREETTUURRNNIINNGG TTHHIISSPPRROODDUUCCTT FFOORR AANNYY RREEAASSOONN::If you have a question or experience a problem with your Black & Decker purchase, go toHTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERSIf you can’t find the answer or do not have access to the internet,call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.Please have the catalog number available when you call.for instant answers 24 hours a day.SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.INSTRUCTION MANUAL |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved