Menu
Black & Decker Freewire Home Automation Starter Kit Instruction Manual
            |
PLEASE FOLLOW THE SEQUENCE LAID OUT IN THIS MANUAL TO AVOID CONFUSIONStep by step instructions to set up the MESSENGER HUB:A Quick Note Before You Set Up The MESSENGER HUB:WARNING: For indoor use only. If a FREEWIRE product is exposed to rain or moisture, immediately disconnect the FREEWIRE productfrom the AC outlet to reduce the risk of electric shock or fire and consult authorized service personnel.WARNING: Use only incandescent bulbs (up to 500 watts total) in lamps that are to be controlled by the Messenger Hub.Each receiver has a specific address made up of a HOUSE CODE (bottom dial) and a UNIT CODE (upper dial) which is used to communicatewith the MESSENGER HUB.The function of the HOUSE CODE is to prevent interference from another FREEWIRE or other compatible system. If you experienceinterference with another system at any time, which may result in unexpected turn on/off of devices plugged into either system, unplug allFREEWIRE devices immediately until (1) the source of the interference is identified and eliminated through selection of a different HOUSECODE to ensure that neither system causes unintended operation of the other system or (2) a blocking filter, Black and Decker Model numberPZZ01, is installed. Call 1-888-678-7278 to order. Professional installation recommended. If you cannot identify the source of interference bytalking with neighbors who are using a FREEWIRE or compatible system and you do not want to install a blocking filter, or if you have anyquestions about identifying or eliminating interference, please call 1-800-544-6986 before plugging in or using any FREEWIRE device.Step 1:Plug the MESSENGER HUB into any operational AC outlet within your home.Rotate antenna to the upright position. Open the front door to expose the controlpanel as shown in Figure 1. NOTE: Placing the MESSENGER HUB on theinside wall closest to driveway or entry way, will often maximize range of theKEY CHAIN REMOTE.Step 2:Select a HOUSE CODE on the MESSENGER HUB, any letter A - P. (Note: Thehouse code you select for the MESSENGER HUB will dictate what letter you willselect for all of the RECEIVERS you plan to control with this MESSENGER HUB.)Step 3:Select a UNIT CODE on the MESSENGER HUB, any number 1 - 16. The numberand corresponding color you pick will control the lamp outlet located on theunderside of this MESSENGER HUB. (If you select the same number and samehouse code for any additional receivers on this system they will operate in conjunction with this hub.)Step 4:Synchronize your INDOOR REMOTE with your MESSENGER HUB so they understand how to communicate with each other. (Note: Anyadditional remote that is introduced to the system must also be synchronized.)To synchronize, move the MESSENGER HUB slide switch to LEARN.While facing the MESSENGER HUB, press and hold the middle “ON” button of the INDOOR REMOTE for 5seconds - Figure 2. Be sure to see the green light flash on the MESSENGER HUB. The flash will indicatethat the MESSENGER HUB is now synchronized with the INDOOR REMOTE.Now, move the slide switch on the MESSENGER HUB to RUN.(Note: Door cannot be closed while MESSENGER HUB is in the LEARN mode.)Step 5:Turn lamp on first, then plug into the receptacle on the underside of the MESSENGER HUB. Use onlyincandescent bulbs up to 500W. Be sure the lamp has been turned on prior to plugging into MESSENGERHUB.Press the Local Lamp “ON/OFF” button on the MESSENGER HUB to check that the MESSENGER HUB isoperating correctly. You will hear a “click” when the MESSENGER HUB turns this lamp on and off.You are now ready to operate the lamp connected to this MESSENGER HUB with the INDOOR REMOTE.Unit Code DialHouse Code Dial1ON OFF12346759810121113151614ROOM COLORMOOD 2MOOD 1 HOUSEONOFFONOFFONOFFONOFFONOFFONOFFPressmiddle“ON”button for 5seconds2On/Off ButtonRun / Learn Slide SwitchPlug Receptacle6621538-00 FW3000 MANUAL 1/5/04 11:02 AM Page 6 |
Related manuals for Black & Decker Freewire Home Automation Starter Kit
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved