Menu
Black & Decker FS84 Instruction Manual
  | |
Contents |
WARNING: FOR SAFE OPERATION READ INSTRUCTION MANUAL.IMPORTANT SAFETY INSTRUCTIONSWARNING: When using electric tools basic Safety precautions should always be followed to reduce therisk of fire, electric shock, and personal injury including the following:1. This manual contains important safety and operating instructions.2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2)battery, and (3) product using battery.3. CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs. Other types ofbatteries may burst causing personal injury and damage.4. Do not expose charger to rain or snow.5. Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electricshock, or injury to persons.6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnectingcharger.7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damageor stress.8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord couldresult in a risk of fire, electric shock or electrocution.a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed extension cordsshould be used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If theextension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdooruse can also be used for indoor work. The letters “W” or “WA” on the cord jacket indicate that the cord issuitable for outdoor use.b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and toprevent loss of power and overheating. The smaller the gauge number of the wire, the greater thecapacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than oneextension to make up the total length, be sure each extension contains at least the minimum wire size.CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDSNAMEPLATE RATING AMPS – 0 – 10.0Total Extension Cord Length (ft) 25 50 75 100 125 150Wire Gauge 18 18 16 16 14 14• Use only the supplied charger when charging your drill. The use of any other charger could damage the drillor create a hazardous condition.• Use only one charger when charging.• Do not attempt to open the charger or the drill. There are no customer serviceable parts inside. Return to anyauthorized Black & Decker service center.• DO NOT incinerate the drill or battery packs even if they are severely damaged or completely worn out. Thebatteries can explode in a fire.• Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from the battery cellsmay occur under extreme usage, charging or temperature conditions. This does not indicate a failure.However, if the outer seal is broken and this leakage gets on your skin:a. Wash quickly with soap and water.b. Neutralize with a mild acid such as lemon juice or vinegar.c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seekimmediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.SAVE THESE INSTRUCTIONS FOR FUTURE USECHARGING THE POWER PACKTHE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFOREATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.The 3 hour charger is designed to use standard household 120 volt 60 Hz power.1. Remove the power pack from the tool, as shown in Figure 1.2. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.3. Insert the power pack into the charger and let it charge for 3 hours. (Figure 2)4. Remove pack from the charger and place in tool. (Figure3) NOTE: To remove the battery from the saw,press in on the release buttons on both sides of the battery and pull out.IMPORTANT CHARGING NOTES1. After normal usage, your power pack should be fully charged in 3 hours or less. If the power pack isrun-down completely, it may take up to 6 hours to become fully charged. Your power pack was sentfrom the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 3hours.2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This is importantand will prevent serious damage to the power pack. Longest life and best performance can be obtainedif the power pack is charged when the air temperature is about 75°F.3. While charging, the charger may hum and become warm to touch. This is a normal condition and doesnot indicate a problem.4. If the power pack does not charge properly—(1) Check current at receptacle by plugging in a lamp orother appliance. (2) Check to see if receptacle is connected to a light switch which turns power off whenyou turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F to105°F. (4) If the receptacle and temperature are OK, and you do not get proper charging, take or sendthe power pack and charger to your local Black & Decker service center. See Tools Electric in yellowpages.5. The power pack should be recharged when it fails to produce sufficient power on jobs which were easi-ly done previously. DO NOT CONTINUE using saw with its power pack in a depleted condition.6. To prolong power pack life, avoid leaving the power pack on charge for more than 8 hours. Althoughovercharging is not a safety concern, it can significantly reduce overall power pack life.7. When the battery is inserted into the charger, the red “Charging Indicator” light will come on indicatingthat there is contact between the battery and charger. The light will stay on as long as the battery is in thecharger and the charger is plugged into a working outlet. It WILL NOT flash, go out or change to adifferent color when the charging cycle is complete.THE RBRC™ SEALThe RBRC™ (Rechargeable Battery Recycling Corporation)Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recycle the battery(or battery pack) at the end of its useful life have already been paid by Black & Decker. In someareas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid wastestream and the RBRC program provides an environmentally conscious alternative.RBRC in cooperation with Black & Decker and other battery users, has established programs in the UnitedStates and Canada to facilitate the collection of spent nickel-cadmium batteries. Help protect our environmentand conserve natural resources by returning the spent nickel-cadmium battery to an authorizedBlack & Decker service center or to your local retailer for recycling. You may also contact your local recyclingcenter for information on where to drop off the spent battery, or call 1-800-8-BATTERY.FULL TWO-YEAR HOME USE WARRANTYBlack & Decker (U.S.) Inc. warrants this product for two years against any defects in material orworkmanship. The defective product will be replaced or repaired at no charge in either of twoways.The first, which will result in exchanges only, is to return the product to the retailer from whom itwas purchased (provided that the store is a participating retailer). Returns should be made withinthe time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proofof purchase may be required. Please check with the retailer for their specific return policyregarding returns that are beyond the time set for exchanges.The second option is to take or send the product (prepaid) to a Black & Decker owned orauthorized Service Center for repair or replacement at our option. Proof of purchase may berequired. Black & Decker owned and authorized Service Centers are listed under “Tools-Electric” in the yellow pages of the phone directory.This warranty does not apply to accessories. This warranty gives you specific legal rights andyou may have other rights which vary from state to state and province to province. Should youhave any questions, contact the manager of your nearest Black & Decker Service Center. Thisproduct is not intended for commercial use.1-800-54-HOW-TOBEFORE RETURNING THIS PRODUCTFOR ANY REASON PLEASE CALLIF YOU SHOULD EXPERIENCE A PROBLEMWITH YOUR BLACK & DECKER PURCHASE,CALL 1-800-54-HOW-TO (1-800-544-6986).IN MOST CASES, A BLACK & DECKER REPRESENTATIVECAN RESOLVE YOUR PROBLEM OVER THE PHONE.IF YOU HAVE A SUGGESTION OR COMMENT,GIVE US A CALL. YOUR FEEDBACK IS VITALTO THE SUCCESS OF BLACK & DECKER’S QUALITYIMPROVEMENT PROGRAM.(544-6986)VEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DEGARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR ELPRODUCTO.INSTRUCTION MANUALCATALOG NUMBERS. FS84, FS132, FS156, PS130, PS140, PS1458888 .... 4444 VVVV,,,, 1111 2222 VVVV,,,, 1111 3333 .... 2222 VVVV,,,, 1111 4444 .... 4444 VVVV,,,, 1111 5555 .... 6666 VVVV,,,, &&&& 1111 8888 VVVVPPPP OOOO WWWW EEEE RRRR PPPPAAAA CCCC KKKK SSSSKEY INFORMATION YOU SHOULD KNOW:•Battery pack must be charged for three hours before initial use.•The batteries in your new power pack are not fully charged! First read the safetyinstructions below. Then follow charging notes and procedures.Cat Nos. FS84 / FS132 / FS156 / PS130 / PS140 / PS145 Form No. 154804 (JUL99)Copyright © 1999 Black & Decker Printed in ChinaFIG. 1 FIG. 2 FIG. 3See ‘Tools-Electric’– Yellow Pages –for Service & SalesImported byBlack & Decker (U.S.) Inc.,701 E. Joppa Rd.Towson, MD 21286 U.S.A.YOU'VE GOT THE TOOLNOW GET THE KNOW-HOWhttp://www.blackanddecker.comGUIDE D’UTILISATIONRENSEIGNEMENTS IMPORTANTS•Il faut charger l’ensemble de piles pendant trois heures avant de s’en servir.•Les piles de l’ensemble ne sont pas complètement chargées. Lire d’abord les mesuressuivantes. Suivre ensuite les notes relatives au chargement.AVERTISSEMENT : POUR S’ASSURER DU FONCTIONNEMENT SÛR, LIRE GUIDE D’UTILISATION.IMPORTANTES MESURES DE SÉCURITÉmesures de sécurité : chargement1. Le présent guide renferme d’importantes directives relatives à la sécurité et au fonctionnement.2. Avant d’utiliser le chargeur de piles, bien lire toutes les directives et les mises en garde qui se trouventsur (1) le chargeur de piles, (2) l’ensemble de piles et (3) le produit utilisant l’ensemble de piles.3. MISE EN GARDE : Afin de minimiser les risques de blessures, charger seulement des ensembles depiles Black & Decker. D’autres types de piles pourraient exploser et causer des blessures et des dom-mages.4. Protéger le chargeur de la pluie et de la neige.5. L’utilisation d’accessoires non recommandés ni vendus par Black & Decker présente des risques d’in-cendie, de secousses électriques ou de blessures.6. Il vaut mieux tirer sur la fiche que sur le cordon pour débrancher le chargeur afin de minimiser lesrisques de dommages à la fiche et au cordon.7. S’assurer que le cordon est situé de sorte qu’on ne puisse marcher dessus, y trébucher, l’endommagerou le soumettre à toute autre contrainte.8. Utiliser un cordon de rallonge seulement en cas d’absolue nécessité. L’utilisation d’un cordon de ral-longe inapproprié présente des risques d’incendie ou de secousses électriques.a. Les cordons bifilaires peuvent être utilisés avec un cordon de rallonge muni de 2 ou de 3 fils. Il fautseulement utiliser des cordons de rallonge à gaine ronde homologués par l’organisme américainUnderwriters Laboratories (U.L.). Lorsque le cordon de rallonge est utilisé à l’extérieur, il doit être prévuà cet effet. Tout cordon extérieur peut servir à l’intérieur. Les lettres «W» ou «WA» sur la gaine du cor-don indiquent que celui-ci convient pour une utilisation à l’extérieur.b. Les cordons de rallonge doivent être faits de conducteurs de calibre approprié (AWG ou jauge améri-caine des fils) par mesure de sécurité et afin de prévenir les pertes de puissance et les surchauffes. Lenuméro de calibre du fil est inversement proportionnel à la capacité du cordon. Ainsi, un cordon decalibre 16 a une capacité supérieure à un cordon de calibre 18. Lorsqu’il est nécessaire d’utiliser plusd’un cordon de rallonge, veiller à ce que chaque cordon ait au moins le calibre minimal.TABLEAU POUR LE CALIBRE MINIMAL (AWG) DES CORDONS DE RALLONGEINTENSITÉ (A) - PLAQUE SIGNALÉTIQUE – 0 – 10,0Longueur totale du cordon de rallonge (pi) 25 50 75 100 125 150Calibre de fil 18 18 16 16 14 149. Utiliser seulement le chargeur fourni pour charger la perceuse. L’utilisation de tout autre chargeur peutendommager la perceuse et être dangereuse.10. Utiliser un seul chargeur à la fois.11. Ne pas tenter de démonter le chargeur ni la perceuse. L’utilisateur ne peut les réparer. En confier lesréparations à un centre de service autorisé Black & Docker.12. NE PAS incinérer la perceuse ni les ensembles de piles même si ceux-ci sont très endommagés ou com-plètement usés. La chaleur des flammes risque de les faire exploser.13. Ne pas incinérer les piles. La chaleur des flammes risque de les faire exploser. Il peut se produire une |
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved