Black & Decker ElectroMate 90556511 Instruction Manual

Also see for ELECTROMATE 400: User manual

Contents

important safety instructions

5WARNING: TO REDUCE THE RISK OF INJURY:Follow these instructions and those published by the battery manufacturer and manufacturer of any equipmentyou intend to use with this unit. Review cautionary markings on this unit, on engine and on any appliances to beused with this unit.INTRODUCTIONThank you for purchasing theBlack & Decker VEC026BD Electromate ® 400. Please read this guide carefullybefore use to ensure optimum performance and avoid damage to the unit or articles connected to the unit.FEATURES• Powers 110/120 volt AC appliances• Powers 12 volt DC appliances• Jump-starts vehicle engines• Built-in inflator• Built-in 400 watt inverter• Includes non-spillable, maintenance-free, heavy-duty, sealed battery• Safe to use, transport and store• Alternator check• Reverse polarity connection warning• Detachable jumper cables• Requires no maintenance (other than recharging) for optimum operation• Rechargeable with built-in AC charger• Unique compact design provides completely portable 12 volt DC power• Molded high-impact case is tough and durable• Built-in area light for night time roadside repairs and use in remote locations without utility power• Battery charge level indicatorsControls and IndicatorsFront View Back ViewThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this devicemay not cause harmful interference, and (2) this device must accept any interference received, including interferencethat may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.4• Have plenty of fresh water and soap nearby in case battery acid contacts skin.• If battery acid contacts skin or clothing, wash immediately with soap and water for at least 10 minutes and getmedical attention immediately.• Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or power station• Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead acidbattery. A lead acid battery can produce a short circuit current high enough to weld a ring, or similar metalobject, to skin, causing a severe burn.• Do not wear vinyl clothing when jump-starting a vehicle when jump-starting a vehicle, friction can causedangerous static-electrical sparks.• Jump-start procedures should only be performed in a safe, dry, well-ventilated area.• Always store battery clamps when not in use. Never touch battery clamps together. This can cause dangeroussparks, power arcing and/or explosion.• When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and besure to keep all clamps, cords, clothing and body parts away from moving vehicle parts.• Never allow RED and BLACK clamps to touch each other or another common metal conductor — this couldcause damage to the unit and/or create a sparking/explosion hazard.a) For negative-grounded systems, connect the POSITIVE (RED) clamp to the POSITIVE ungrounded batterypost and the NEGATIVE (BLACK) clamp to the vehicle chassis or engine block away from the battery. Do notconnect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal partof the frame or engine block.b) For positive-grounded systems, connect the NEGATIVE (BLACK) clamp to the NEGATIVE ungrounded batterypost and the POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery. Do notconnect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal partof the frame or engine block.• If the connections to the battery’s POSITIVE and NEGATIVE terminals are incorrect, the Reverse PolarityIndicator will light (red) and the unit will sound a beep. Disconnect clamps and reconnect to battery with correctpolarity.• Always disconnect the NEGATIVE (BLACK) jumper cable first, followed by the POSITIVE (RED) jumper cable,except for positive grounded systems.• Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, protectexposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).• Place this unit as far away from the battery as DC cables permit.• Never allow battery acid to come in contact with this unit.• Do not operate this unit in a closed area or restrict ventilation in any way.• FIRST AID – SKIN: If battery acid comes in contact with skin, rinse immediately with water, then washthoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention.EYES: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seekimmediate medical attention.• IMPORTANT: This unit is delivered in a partially charged state. Fully charge unit with a household extension cord(not supplied) for a full 48 hours before using for the first time. You cannot overcharge the unit using the ACcharging method.• All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure allswitches are in the OFF position before connection to a power source or load.• Never insert anything other than the supplied recommended appliance power/recharging cords into the 12 voltDC power outlet on this unit.• Do not use any accessory that is not recommended or provided by the manufacturer.• Do not use this unit to operate appliances that need more than 5 amps to operate from the 12 volt DC accessoryoutlet.• This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6 voltor 24 volt battery system.• This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate avehicle that does not have a battery installed.• Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after therecommended number of attempts, discontinue jump-start procedures and look for other problems that mayneed to be corrected.• Do not use this jump-starter on a watercraft. It is not qualified for marine applications.• Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage,use and recharging. To avoid possible damage that may shorten the unit’s working life, protect it from directsunlight, direct heat and/or moisture.• Read And Understand This Instruction Manual Before Using This Unit.SAVE THESE INSTRUCTIONSUNIT FRONT PANELAIR VENTSDC POWER SUPPLY PANELAC POWER SUPPLY PANELRUBBER HANDLEJUMPER CABLECONNECTORINFLATORAC CHARGER12 VOLT DC ADAPTERSTORAGECOMPARTMENT90556511 VEC026BD.qxp:VEC026BD ManualENSP 061808 12/11/09 2:02 PM Page 4