Black & Decker 618492-01 Instruction Manual

Contents

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,and other construction activities. Wear protective clothing and wash exposed areaswith soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin maypromote absorption of harmful chemicals.WARNING: Use of this tool can generate and/or disburse dust, which may causeserious and permanent respiratory or other injury. Always use NIOSH/OSHA approvedrespiratory protection appropriate for the dust exposure. Direct particles away from face andbody.General Safety RulesWARNING! Read and understand all instructions. Failure to follow all instructions listedbelow, may result in electric shock, fire and/or serious personal injury.SAVE THESE INSTRUCTIONS• Read and understand drill instruction manual before using this tool. It containsadditional safety rules and instructions not covered here.Electrical Safety• Check for wires. plumbing, or hazardous conditions around and obscured by thework surface. Failure to do so may result in electric shock or other personal injury.• Always hold the handle with one hand and the drill with the other hand when drivingscrews. Contact with “live” wire will make exposed metal parts of tool and drill “live” andshock the operator.Personal Safety• Use safety equipment. Always wear appropriate eye, respiratory, and foot protection.Failure to do so may result in personal injury.• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep yourhair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long haircan be caught in moving parts. Air vents cover moving parts and should be avoided.• Keep hands and feet away from main body assembly when depressing tool or whenholding tool upright with a drill attached which has sufficient weight by itself todepress tool. Injuries may be caused by pinch points and sharp screw tips.• Do not use tool while standing on a ladder or step stool. Overreaching can cause a lossof balance and subsequent fall.Tool Use and Care• Do not expose tool to rain or wet conditions. Discontinue use if hex shaft does notspin freely. Rust may cause moving parts to seize.• Do not use trigger lock on drill if equipped with one. An unsafe condition may result ifscrew is unintentionally driven.• Always check tool before use:a. Examine for broken parts.b. Turn hex shank by hand to ensure free rotation.c. Verify clear plastic window on sliding barrel is fully closed.d. Verify proper operation of depth adjustment slider.e. Cycle tool once.• If tool is damaged or not functioning properly, have it serviced before using. Manyaccidents are caused by poorly maintained tools.• After use, always remove drill from tool. Do not store with drill attached to hex shaft.Tool with attached drill can more easily fall if bumped.• For use ONLY with drywall and decking type screws number #6 & #8 Phillips orRobertson head, 1.5 to 3 inches in length. Other screws may jam.• Do not remove screws from the clear tube through the screw filter. A jam may occur.Service• Tool service must be performed only by qualified repair personnel. Service ormaintenance performed by unqualified personnel could result in a risk of injury.• When servicing a tool, use only identical replacement parts. Follow instructions inthe Maintenance section of this manual. Use of unauthorized parts or failure to followMaintenance Instructions may create a risk of electric shock or injury.Specific Safety RulesWARNING: Some dust created by power sanding, sawing, grinding, drilling, andother construction activities contains chemicals known to cause cancer, birth defectsor other reproductive harm. Some examples of these chemicals are:• lead from lead-based paints,• crystalline silica from bricks and cement and other masonry products, and• arsenic and chromium from chemically-treated lumber (CCA).Your risk from these exposures varies, depending on how often you do this type of work. Toreduce your exposure to these chemicals: work in a well ventilated area, and work withapproved safety equipment, such as those dust masks that are specially designed to filterout microscopic particles.VEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO YPÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTEINSTRUCTIVO ANTES DE USAR EL PRODUCTO.Catalog # FS100SF, ASF100EX Form No.618492-01, Rev. 2 (Dec. ‘04)Copyright © 2004 Black & Decker Printed in MexicoINSTRUCTION MANUALCatalog Numbers FS100SF, ASF100EXSSSS cccc rrrreeee wwww FFFF eeee eeee dddd eeee rrrrBEFORE RETURNING THIS PRODUCTFOR ANY REASON PLEASE CALL1-800-544-6986IF YOU SHOULD EXPERIENCE A PROBLEMWITH YOUR BLACK & DECKER PRODUCT,CALL 1-800-544-6986BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No.,TYPE No., AND DATE CODE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CANRESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT,GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.235 647 89 10121113Screw Feeder Diagram1. Screw Filter2. Rear Support3. Front Support4. Clear Tube5. Sliding Barrel6. Main Body Assembly7. Quick Change Bit Holder8. Release Tabs9. Extension Assembly10. Handle11. Drive Bit(Phillip/Robertson)Diagramme de l'alimenteur à vis1. Filtre de vis2. Support arrière3. Support avant4. Tube transparent5. Canon coulissant6. Corps principal7. Porte-embout à changementrapide8. Languettes de dégagement9. Rallonge10. Poignée11. Embout (Phillips/Robertson)Diagrama del alimentador detornillos1. Filtro de tornillos2. Soporte trasero3. Soporte delantero4. Tubo transparente5. Cilindro deslizante6. Conjunto del cuerpo principal7. Portabrocas de recambio rápido8. Lengüetas de liberación9. Conjunto de extensión10. Empuñadura11. Broca impulsora(Phillip / Robertson)123711109865 41

/ 4

Related manuals for Black & Decker 618492-01