Menu
Barska AX11646 User Manual
Also see for AX11646: User manual
  |
User’s Manual forBiometric/Key Pad SafeWARNING- Safe can be opened by either Fingerprint, PIN code,and/or Emergency Keys.- If user resets safe to Factory Default mode: Only theEmergency Key or the Factory Default PIN code 1234can open the safe.- Register both Fingerprint and PIN code to disableFactory Default mode.- Register at least two different fingerprints and test a fewtimes before closing the safe door.- Test with a non-registered fingerprint. If the safe opens,the safe is still in Factory Default mode.- Avoid leaving safe door open and unattended; it will allowunauthorized individuals to add their fingerprints and/orreprogram the safe, gaining full access to the safe andthe contents.- Test the Emergency Keys and store them in a secureplace, NOT inside of the safe.- To maximize the security and performance of the safe,test registered fingerprints every 6 months.Read all instructions before using this safe.A. Initialization ButtonB. Battery CompartmentC. BoltsD. Fingerprint ScannerE. Indicator LightsA BCIDFGEHF. Enter ButtonG. Key PadH. KnobI. Logo Plate andEmergency Key Access* Actual model may varyGETTING STARTED1. Remove Emergency Keys from accessory package- To expose the Emergency Key Access, remove Logo Plate(I) screws with provided tool- Insert Emergency Key into key access, push and turncounter-clockwise- Turn the Knob (H) clockwise to openNote: Store Emergency Keys in a secure place, NOT inside ofthe safe2. Continue with INSTALL BATTERIESINSTALL BATTERIES1. With safe door open, remove Battery Compartment (B) cover- Insert 4 AA batteries and restore battery cover- Continue with FINGERPRINT REGISTRATIONFINGERPRINT REGISTRATIONIMPORTANT: The safe is in either Factory Default mode orPre-registered mode, test safe to determine factory settingsbelowFactory Default mode: Safe can be opened with ANYfingerprint(s)Pre-registered mode: Safe can NOT open with any fingerprint(s)During registration the door must remain open and Bolts (C)must be in the retracted position. Otherwise, the fingerprint willnot be savedTo retract bolts:- Insert Emergency Key into key access, push and turncounter-clockwise- Turn the Knob (H) clockwise to retract bolts1. Press and release Initialization Button (A)2. Immediately place a finger on the Fingerprint Scanner (D)- Hold finger still- Two beeps will be heard recognizing the fingerprint; followedby one long beep- Remove finger- Registration is completeSuccessful RegistrationRegistration is successful when two short beeps are heard,followed by one long beepUnsuccessful RegistrationRegistration failed if two short beeps are heard, followed bythree short beeps3. To register another fingerprint, repeat steps 1 - 24. Continue with TEST A (NON) REGISTERED FINGERPRINTFingerprint Memory FullIf the Indicator Lights (E) flash and beep twice followed by a fewgreen flashes, it indicates the memory is full. Refer to DELETESTORED FINGERPRINTS AND PIN CODE / RESET TOFACTORY DEFAULT MODE for more optionsTEST A (NON) REGISTERED FINGERPRINT1. Test multiple Non-Registered fingerprints- Close safe door and lock by turning the Knob (H) counter-clockwise- To begin the testing process, press and release EnterButton (F)- Place a non-registered finger on the Fingerprint Scanner (D)- Door should NOT open; three short beeps will be heard- If the door opens with a non-registered fingerprint,registration was unsuccessful; the safe remains in FactoryDefault modeIMPORTANT: If registration was unsuccessful repeat stepsunder FINGERPRINT REGISTRATION, and test non-registeredfingerprint2. Test Registered fingerprint- Close safe door and lock by turning the Knob (H) counter-clockwise- To begin the testing process, press and release EnterButton (F)- Place a registered finger on the Fingerprint Scanner (D)- Door should OPEN, one long beep will be heard, turn theKnob (H) clockwise to open the safe- Fingerprint registration was successful3. Continue with PIN CODE REGISTRATIONPIN CODE REGISTRATIONIMPORTANT: Safe only retains one PIN code; Factory DefaultPIN code is 12341. Press and HOLD number “1” key until the green IndicatorLight (E) turns on, release button- Enter Factory Default PIN code 1234, press Enter Button(F), one long beep will be heard- Enter new PIN code (four to eight digits), press Enter Button(F), two short beeps will be heard- Re-enter new PIN code, press Enter Button (F), one longbeep will be heard- Registration is complete2. If you hear three short beeps with red/green Indicator Lights(E) flashing, it indicates the new PIN code registration wasunsuccessful, repeat step 13. Continue with TEST A (NON) REGISTERED PIN CODESee reverse side for more information 6/13BC354UnlockLock |
Related manuals for Barska AX11646
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved