Menu
Bantam e-STATION TWO-METER Quick Manual
  |
Thank you for purchasing e-STATION TWO-METER. Please read this entire operating manual completely and attentively as it containsimportant information and safety notes, therefore you need to keep this manual in a safe place, and be sure to pass it on to the new ownerif you ever dispose of TWO-METER.TWO-METER is a very sophisticated electronic device that controlled by high performance microprocessor and precise resistors. It hasthree functions of ‘watt-meter’, ‘battery checker’ and self-balancer. Those functions are essential for electric flyers to ensure safe batterycondition and to measure the electric consumptions of the power system. And also, the built-in self-balancer can equalize the individualvoltages instantly. TWO-METER can handle all types of Lithium batteries(LiPo, LiIo, LiFe) consisting of series-wired cells, but the batterypack has to have a balancing plug for checking voltages.When connect the individualconnection cable to TWO-METER, itshould be matched with the plug ofthe battery pack. Suitable adaptorboards are available for various typesof connector from the batterymanufacturers.(for PolyQuest EAC123, forKokam/Graupner/Robbe EAC128, forFlightPower/ThunderPower EAC129,and for Align EAC124)Basic operationBattery checker programThis feature can be used to check the residual battery capacity and the voltage of individualcells.-. Select the program by pressing ‘SELECT’ button to suit the type of battery being measured.-. And press ‘ENTER’ to go to the next screen.-. There are two programs which are voltage checker and self-balancing. Select ‘LiPo Check’program using ‘SELECT’ button and press ‘ENTER’.TWO-METER is activated when the battery is connected to the unit. For the battery checkerfunction, connect the battery pack to the individual port via a suitable adaptor board, or connect thebattery to the cable of ‘Power source’ for watt meter.!!SpecificationLi-Po 1SLi-Po 2SLi-Po 3SLi-Po 4SLi-Po 5S+-+-+-+-+-Li-Po 6S+-Watt LiPoLiFe LiIo◀ ◀‘ENTER’LiPo CheckLiPo Balance◀ ◀‘ESC’‘ENTER’‘ESC’Input power: Max. 60.0V (both on watt-meter and battery checker)Max. current: 100A (watt-meter)Min. operating voltage: 7.2VCurrent consumption: 20mA at battery checker programDimension: 100 x 60 x 23 mmLiPo-3S 12.503V97% E‘ENTER’‘ESC’4.18 4.16 4.160.00 0.00 0.00It shows the type of battery and number of cell-count at upper right, and output voltage. At lowerline, it displays the residual capacity at percentage and visual graph.The individual voltages are shown from the first cell at upper right.LiPo-3S 12.503V97% UNBALANCEDIf the voltage are out of balance, it warns and shows the voltage difference from the highest tolowest one. You need to let them balanced, or check the cells and cables carefully.Self-balancing programThis program can equalize the individual voltages to their lowest one.-. Select the matched type of Lithium battery using ‘SELECT’ button.-. And press ‘ENTER’ to start to balance .LiPo CheckLiPo Balance ◀ ◀‘ENTER’‘ESC’LiPo-3S 12.503VBalancingAs the balancing job goes on, you can see the individual voltage by pressing ‘ENTER’ button.When the balancing job is completed, the beep sounds 20 times.(You can set the beep sound ‘OFF’ by pressing ‘SELECT’ button for more than three seconds. Oryou can set it ‘ON’ by doing the job again. The default is ‘ON’.)To protect the battery from the over-discharge, there are minimumvoltages to be balanced for each type of Lithium batteries. If the anyindividual voltage is lower than the limit, there shows an error message.LiPo/LiIo: 3.0V, LiFe: 2.0V! |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved