Baldor 602e-mt Instruction Manual

Also see for 602E-MT: Instruction manual

Baldor 602e-mt Instruction Manual Manual pdf 1 page image

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MN914Instruction Manual For Belt Grinder-Buffer Model 602E-MT1MN914SAFETY NOTICE:WARNING statements describe conditions that may lead to personnel injury including potentially fatal injuries if themachine is not properly used and warnings are not properly followed.Caution statements describe conditions that may lead to equipment damage.Electrical shock can cause serious or fatal injury. Only qualified personnel should install, maintain or troubleshootthis equipment.WARNING: Do not operate this grinder-buffer until you are sure that you are completely familiar with the safe operationof the grinder-buffer, all accessories and safety equipment. Improper use can lead to severe injury. Thismanual defines proper use of this equipment. Before using this equipment for any other use, please seekexpert advise if you do not understand any procedure or operation concerning this grinder-buffer or thismanual.WARNING: Prevent electrical shock hazard and accidental machine operation. Always disconnect grinder-buffer fromthe power source before servicing, changing accessories (such as belt, wire wheel, tool rest, spark arrestor,etc.) or before performing maintenance.WARNING: Avoid accidental starting. Make sure switch is in “OFF” position before connecting to power source.WARNING: Be sure the system is properly grounded before applying power. Do not apply power before you ensure thatgrounds are connected. Electrical shock can cause serious or fatal injury. Follow the National Electrical Code(NEC) and local codes for the safe installation of this equipment.WARNING: Always use safety glasses with side shields (or full face shield) when operating grinder. Do not use ordinaryeyeglasses. Also use face or dust mask if cutting operation is dusty.WARNING: Unsuitable accessories or attachments added to this machine can create hazards. Baldor accessories arespecifically designed to be used with this grinder-buffer. Use accessories or attachments only in the properintended manner. Accessories or attachments obtained from another source may cause hazards. Consult themanufacturer before use.WARNING: To prevent injury, avoid contact with the wire wheel or belt or disc. The abrasive belt when running is anaggressive cutting tool. Extra care should be exercised when using coarse grit belts because of their rapidcutting action. Severe burns or cuts may result from contact.WARNING: Keep guards in place and in working order. Guards are design to prevent injury. Never operate this equipmentif a guard is damaged, missing or improperly installed.WARNING: Remove adjusting keys and wrenches from this product after use. Check to see that keys and adjustingwrenches are removed from grinder-buffer before turning it on. Projectiles can cause severe injury toyourself or others.WARNING: Keep work area clean and well lighted. Clutter and poor lighting invites accidents.WARNING: Don’t use in dangerous environment. Don’t use grinder-buffers in damp or wet locations, or expose them torain. Electrical shock can cause serious or fatal injury. Follow the National Electrical Code (NEC) and localcodes for the safe installation of this equipment.WARNING: Do not wear loose clothing, neckties, rings, bracelets, or other jewelry to get caught in moving parts. Nonslipfootwear is recommended. Wear protective hair covering to contain long hair.WARNING: Secure work. Use clamps to secure the work piece when practical. It’s safer than using your hand and itkeeps hands away from wheel or belt.WARNING: Check for damaged parts. Before further use, a guard or other part that is damaged should be carefullychecked to assure that it will operate properly and perform its intended function. Check for alignment ofmoving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affectits operation. A guard or other part that is damaged should be properly repaired or replaced.WARNING: When starting a grinder for the first time, or after installing a replacement belt or wire wheel, it is mostimportant that the operator stand aside for at least one minute of rotation at full speed. This is the correctpractice since a wire wheel can disintegrate if it received damage during shipping or handling.WARNING: Use proper grounded extension cord. Make sure your extension cord is in good condition. When using anextension cord, be sure it is rated for the voltage and current rating of your product. An undersized cord willcause a drop in line voltage resulting in loss of power and overheating. Use the correct wire size dependingon cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the AWGgauge number, the heavier the cord.WARNING: Always wear a dust mask to prevent dust inhalation when adequate ventilation or extraction is not available.WARNING: Dust created during grinding, buffing, sawing, power sanding, drilling, and other activities may containchemicals known to the State of California to cause cancer, birth defects or other reproductive harm.WARNING: Keep children and visitors away. Remove starter keys turn off master switches. Padlock equipment or workarea when not in use.WARNING: Don’t over reach. Keep proper footing and balance at all times. A rotating wheel can catch an article ofclothing and cause personnel injury.WARNING: Never leave grinder-buffer running unattended. Always turn power off after use.Caution: Don’t force grinder-buffer. It will do the job better and safer at the feed rate for which it was designed.Caution: Use right tool. Don’t force tool or attachment to do a job for which it was not designed.Caution: Maintain grinder-buffer with care. Keep grinder-buffer clean for best and safest performance.