Asus CT-479 Installation Manual

CT-479 Installation guide/34Locate the 478-pin socket. Press the lever sideways thenlift it up to a 90º-100º angle to unlock the socket.º ºPosition the CT-479 above the socket such that thesocket corner with small triangle matches the base of thesocket lever (A), then carefully insert the CT-479 intothe socket until it fits in place (B).When the CT-479 is in place, push down the socket leverto secure it. The lever clicks on the side tab to indicatethat it is locked.Make sure that the CT-479 socket is unlocked (A).Position a 479-pin CPU above the CT-479 socket suchthat its marked corner matches the corner with smalltriangle (B).6Carefully insert the CPU into the socket until it fits inplace (A) then use a flat-head screw driver to lock theCPU in place (B).N O T E :N O T E :N O T E :N O T E :N O T E : Make sure that thesocket lever is lifted up to a90º - 100º angle; otherwise,the CT-479 does not fit incompletely.º ºW A R N I N G :W A R N I N G :W A R N I N G :W A R N I N G :W A R N I N G : The CPU fits onlyin one orientation. DO NOTforce the CPU into the CT-479socket to prevent bending thepins and damaging the CPU.Q 2 0 4 7Q 2 0 4 7Q 2 0 4 7Q 2 0 4 7Q 2 0 4 712W A R N I N G :W A R N I N G :W A R N I N G :W A R N I N G :W A R N I N G : The CT-479 fitsonly in one orientation. DONOT force the CT-479 intothe socket to preventbending the pins.Set the jumper according to your processor Front SideBus (FSB). Set the jumper labeled J 1J 1J 1J 1J 1 to pins 1-2 and 4-5for FSB 400, or to pins 2-3 and 5-6 for FSB 533.J1®POWER1CT-479mPGA479MSOCKETJ1FSB400362514362514FSB53312Align the metal clip to the side rail of the CPU cooler (A)and snap the hook of the metal clip into the hole (B).Press down the locking lever and hook its end into theother hole.7Connect the bundled 4-pin power cable to the CT-479power connector labeled P O W E R 1P O W E R 1P O W E R 1P O W E R 1P O W E R 1.13Follow steps 11 and 12 to install the second clip, thistime in the reverse orientation of the first clip.When the CPU cooler is in place, connect the CPU fancable to the CPU fan connector on the motherboard.10Fit the CPU cooler into the retention module. Orient theCPU cooler such that the cleft is on the side with powercable.9Remove the protective film and sticker that covers theThermal Interface Material (TIM) under the CPU cooler.IMPORTANTIMPORTANTIMPORTANTIMPORTANTIMPORTANT• This module works only with qualified ASUSmotherboards and Intel® Pentium ® M processors.Refer to the module box for the list of qualifiedmotherboards and processors.• If necessary, update the motherboard BIOS file.• Visit the ASUS website (www.asus.com) for anupdated list of qualified motherboards andprocessors, and to download the latest BIOS file.• You cannot adjust the CPU voltage when using thismodule.WARNING!WARNING!WARNING!WARNING!WARNING!• Using this module with unqualified motherboardsand/or processors will damage the motherboard,module, and/or processor.®®15-061117001 www.asus.com8Connect the other end of the bundled 4-pin power cableto a 4-pin ATX power connector from the power supplyunit.AAAAABBBBBAAAAABBBBBI M P O R T A N T :I M P O R T A N T :I M P O R T A N T :I M P O R T A N T :I M P O R T A N T : Make surethat the CPU cooler isinstalled properly (i.e., notinclined or tilted) to preventdamage to the module and/or processor.5AAAAABBBBB11AAAAABBBBB

/ 2

Related manuals for Asus CT-479