Acoustic Research AW850 Installation And Operation Manual

Contents

Acoustic Research AW850 Installation And Operation Manual Manual pdf 1 page image

Model AW850Installation andOperation ManualImportant InformationRISK OF ELECTRIC SHOCK.DO NOT OPEN.CAUTION Caution: To reduce the risk of electric shock, do not remove cover (or back). No userserviceable parts inside. Refer servicing to qualified service personnel.Product InformationKeep your sales receipt to obtain warranty parts andservice and for proof of purchase. Attach it here andrecord the serial and model numbers in case you needthem. These numbers are located on the product.Model No.: ______________________________________Purchase Date: __________________________________Dealer/Address/Phone: ___________________________Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Clean only with dry cloth.6. Do not block any ventilation openings. Install in accordancewith the manufacturer’s instructions.7. Do not install near any heat sources such as radiators, heatregisters, stoves, or other apparatus (including amplifiers)that produce heat.8. Protect the power cord from being walked on or pinchedparticularly at plugs, convenience receptacles, and thepoint where they exit from the apparatus.9. Unplug this apparatus during lightning storms or whenunused for long periods of time.10. Refer all servicing to qualified service personnel. Servicingis required when the apparatus has been damaged in anyway, such as power-supply cord or plug is damaged, liquidhas been spilled or objects have fallen into the apparatus,the apparatus has been exposed to rain or moisture, doesnot operate normally, or has been dropped.Care and Maintenance• Always use a soft cloth to clean the speaker andtransmitter. Never use any product containing alcohol orother solvents as they may damage the surface.• Use caution when plugging the power transformer in anAC outlet to avoid the risk of electric shock.• To clean the lantern/speaker: Shut off main power supply.Wipe with damp cloth or use window cleaner. Do not useabrasive cleaners.• Bulb replacement: Replace with MAX 40W type B orListed 13W Self-Ballasted Compact Fluorescent Lamp(candelabra-based bulb).Warning: Do not use bulb-base adapters with this product.This product must be used with candelabra-based bulbsonly.Tour of the Speaker SystemLantern/SpeakerBottom PanelThe bottom panel of the lantern/speaker isprotected by a rubber door. Find the tab onthe right side of the door and pull it downgently to open.AAudiosourceDC INCHANNEL1 2 3R AUDIO LINTransmitter(back panel)Y-adapteraudio cableWARNING: RISK OF INJURY• Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.• Account for small parts and destroy packing material, as these may be hazardous to children.• Use flashlight or alternate light source to light work area during installation.• Assistance may be required to support fixture during installation.• This apparatus must be installed in accordance with all applicable installation rules.• This device must be connected to a mains socket outlet or outlet box with a grounded and protected connection.• To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions.CAUTION: WIRING AND FIXTURE OPERATION• Connect fixture to supply wires rated for at least 90°C (194°F).• Do not use fixture on dimming circuits.• Unit must be mounted higher than 60”.WARNINGTo prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions.Only use attachments/accessories specified by the manufacturer.IntroductionAR’s Outdoor Lantern and Wireless Speaker System puts a new twist on your outdoorlighting: sound! The AW850 eliminates the hardest part of adding speakers to yourhome—running and hiding hundreds of feet of speaker wire. The AR Wireless SpeakerSystem’s RF signal travels with ease through walls, floors, ceilings and other obstacles,delivering high-quality sound and stylish décor. With drift- and static-free receptionalong with outstanding range—up to 150 feet*—the possibilities for enjoying your ARWireless Speaker System are nearly unlimited. The AR Wireless Speaker System iscompatible with most audio sources, such as TVs, DVD players, VCRs, A/V receivers/amps, stereos, computers, and portable devices (CD players, cassette players, MP3setc.).This manual covers various connection options and detailed operating instructions formaking the AR Wireless Speaker System a valued part of your lifestyle. If, after havingreviewed the instructions, you have any questions, please call toll-free1-800-732-6866 or visit www.araccessories.com.*Range may vary according to environment.Setting UpUnpackingBefore you start installing the Outdoor Lantern and Wireless Speaker, make sure youhave the following parts in your package:(1) Lantern/Wireless Speaker(2) WireConnectors(2) MountingScrews(1) Mounting CrossbarMounting the Lantern/Wireless SpeakerBefore you can use the Outdoor Lantern and Wireless Speaker, you must mount it toan outlet box.WARNING: Consult a qualified electrician in case the main supply wiring needs to bechecked or if you’re not certain how to install wiring. Always install wiring connectionsin accordance with local code, ordinances, and the National Electrical Code.Outdoor Lantern andWireless Speaker(2) Caps1. Make sure power is off for the outlet box at the maincircuit breaker.2. Remove the old fixture from the outlet box. Carefullydisconnect its wiring.3. Mount the crossbar to the outlet box using the mountingscrews included in this package.4. Unscrew the center screw on the crossbar and align thetwo side screws so that they are level with each other. Thentighten the center screw.5. Find the copper ground wire coming from the wirelessspeaker. Twist it together with the ground wire coming fromthe outlet box.If the outlet box doesn’t have a ground wire, attach theground wire to the mounting crossbar as shown here.6. Strip 3/4” of insulation from the wire ends coming fromthe speaker. Use pliers to twist the speaker’s stripped endstogether with the wires coming from the outlet box—makesure you match black wire to black and white wire to white.Then snip the ends.7. Attach the wire connectors to the joined ends. If you’d like,you can tie the connectors and ends together with electricaltape.Level8. Place the wireless speaker onto the two side screws on thecrossbar. Secure the speaker onto the wall with the two capsincluded in this package.9. Use silicon caulking to seal the top and sides betweenthe speaker and the wall. Leave the bottom open so thatmoisture can drain.Connecting the Transmitter to an Audio Source1. Plug the stereo plugs on the provided Y-adapteraudio cable into the AUDIO IN jacks on the back ofthe transmitter (make sure to match the colors onthe plugs and jacks).2. Plug the mini-plug end of the provided Y-adapterinto the headphone output of your MP3 player or CDplayer (or audio output jack on your computer).Transmitter (back panel)120V ACwall outletAC PowerAdapterDC INCHANNEL1 2 3R AUDIO LIN3. Connect the small, round plug from the transmitterAC power adapter to the transmitter’s DC IN jack.Plug the other end of the transmitter AC poweradapter into any standard 120V AC wall outlet.Connecting to an A/V ReceiverYou can also connect the transmitter to an A/V Receiver using the mini-jack toRCA adapter included.1. Plug the stereo plugs on the provided Y-adapter audio cable into the AUDIOIN jacks on the back of the transmitter (make sure to match the colors on theplugs and jacks).AA/V ReceiverAudio OutputDC INCHANNEL1 2 3R AUDIO LINTransmitter(back panel)Mini-jack toRCA adapterY-adapteraudio cable2. Plug the mini-plug end of the providedY-adapter into the mini-jack to RCA adapter.3. Connect the stereo plugs on the mini-jack toRCA adapter to the corresponding left andright audio outputs of your A/V receiver,amp, or other audio source.(1) TransmitterPower Adapter(1) 3.5mm toRCA Cable(1) TransmitterNote: This power unit is intended to be correctly oriented in a vertical or floormount position.Note: There is no transmitter ON/OFF switch. The transmitter is designed to beleft plugged in and powered at all times. If you will not be using the AW850 for anextended period of time, unplug the transmitter AC power adapter.Installing/Changing the Lantern Light BulbThe Outdoor Lantern and Wireless Speaker takes a candelabra-base bulb (40W max;bulb not included). For best results, use a clear (non-frosted) 40W bulb. To install orchange the lantern’s bulb:1. Use a small flat tool (like a flat-head screwdriver)to open the top of the lantern’s front door.2. Insert the bulb and screw it into the base.3. Gently close the door until it snaps back intoplace.Important: Handle and dispose of fluorescent bulbsper manufacturer’s directions.L/M/R switch determines if the speaker plays sound in mono as a stand-alone speaker,or plays the left or right track in a stereo pair with an additional AW850Music On/Off button turns the speaker on and offAuto Scan button rescans for the transmitter’s signalVolume +/– buttons adjust the volume levelLight On/Off switch turns the lantern on and offFront PanelPower/Linked indicator (not shown) blinks when the speaker is first powered on; it turnssolid blue when the speaker is tuned to the transmitterWarning: This product is designed to work with line level outputs or headphoneoutputs only. DO NOT connect it directly to speaker outputs as it will permanentlydamage the transmitter.Groundwire(1) mini-jack toRCA adapter

/ 2

Related manuals for Acoustic Research AW850