Menu
Ace DUALBRITE 3009701 User Manual
  | |
Contents | 
© 2005 598-1231-003. Testing1. Remove the existing fixture.2. After screwing the sensor into the wall plate, connect the junc-tion box wires to the light control wires as shown in Figure 1:• Black sensor wire to the black (HOT) house wire.• White sensor wire to all white (NEUTRAL) house and lampwires.• Red (SWITCHED HOT) sensor wire to black lamp wires.3. Mount light fixture according to the instructions that came withyour fixture.2. AimingFigure 2 - Coverage Angles240°8 Ft.100 Ft.Figure 1 - Wiring Sensor HeadDUALBRITE®ReplacementSensor HeadSpecifications:Total Lighting Wattage .. Up to 500 Watts Maximum IncandescentRange .........................up to 70 ft.; up to 100 ft. with Range BoostTime Delay ........................................................1, 5, or 20 minutesDUALBRITE® ....................................Off, 3, 6 hours, Dusk-to-DawnCAUTION:This product is to be used with a U.L. listed raintight or wet location suitable outlet box. Depending on theinstallation, additional hardware may be required.Note: Installation of this light control should be done only bythose with experience in 120 Volt household wiring. Install inaccordance with local codes. Some local codes may require thata licensed electrician install the light control.Models 3009701 / 32099961. InstallationCAUTION: Always turn the circuit breaker off when wir-ing the fixture.For motion sensing, put the ON-TIME switch on the bottom ofthe sensor in the 1, 5, or 20 minute position. When motion is detected,the lights will come on the selected time. Note: The photocell keepsthe lights from turning on in daylight.To keep lights on all night, flip the light switch off for 1 secondthen back on. To return the sensor to the motion sensing mode, flipthe light switch off for 1 second then back on. At dawn, the controlwill return to the motion sensing mode and shut off.For accent lighting, set the DUALBRITE® switch to the 3, 6, orDusk-to-Dawn setting. The lights will turn on dim at sundown forthe set time. When motion is sensed the lights will turn on full brightfor the set ON-TIME period. The lights will return to dim during theset DUALBRITE® period.4. OperationTurn the power back on at the circuit breaker. Turn the lightswitch on.Note: When first turned on wait about 1 1/2 minutes for the circuitryto calibrate.Put the ON-TIME switch on the bottom of the sensor in the TESTposition. You can now walk in front of the unit and the lights will comeon for about 5 seconds. The TEST mode works both day and night.Walk through the coverage area and point the sensor to obtain thedesired coverage area. Adjust sensitivity as needed. Use RANGEBOOST only if required.The coverage area for the sensor is shown in Figure 2. The sensorshould be aimed so that the motion to be detected is in front of andacross the coverage area. The sensor should be aimed looking outat a horizontal angle. To reduce false triggering, point the sensoraway from traffic areas, air conditioners, dryer vents, water pools,or anything which may move or change temperature rapidly.This light control automatically turns on lights when motion isdetected. On-time is selectable from Off, 1, 5, or 20 minutes. Aphotocell keeps the lights off during the day. Patented DUALBRITE®timer provides accent lighting.CAUTION: Do not mount the sensor above or touchingthe lamps. Keep regular PAR-38 lamps at least 1" (25 mm)from the sensor. Halogen lamps should be kept at least2" (51 mm) from the sensor. The sensor bottom must befacing down for best coverage and to avoid water damageand electrical shock.Note: For under-eave installation, rotate the sensor head 180° bybending the sensor towards the clamp bracket. Rotate the sensorbottom clockwise away from the bracket.BLACK Sensor Wire andBLACK Junction Box WireAll WHITE WiresRED Sensor Wire andBLACK Lamp WiresOptional: Connect additional load across the white andred sensor wires. Total lighting load including lamp-heads on fixture(s) must not exceed 500W (4.2A).Junction BoxLampHolders |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved