Accuride Ascent CB LIFT0019 Quick Installation Manual

Accuride Ascent CB LIFT0019 Quick Installation Manual Manual pdf 1 page image

ComponentsQUICK INSTALLATION GUIDECABINET PREPARATIONINSTALLATION PROCEDURE© 2009 Accuride International Inc. 3700-9529-(1217)-MK135-N-0809-PBAACCURIDE INTERNATIONAL INC.12311 Shoemaker AvenueSanta Fe Springs, CA 90670TEL (562) 903-0200FAX (562) 903-0208www.accuride.comManufacturing, Engineering, and SalesUnited States • Germany • Japan • Mexico • United Kingdom • ChinaWARNINGThe Ascent warranty is voided if the product ismodified in any way or the instructions for the productare not followed.Read all instructions before installing and operating theCBLIFT-0019.CAUTION!• Do not operate the lift without attaching adequatecounterbalance weights. See the weight matrix on theproduct technical sheet.! WARNING1 ea1 ea1 ea1 ea1 ea1 ea8 ea28.35"[720]min.7.87" [200] min.122.30"[58.4].59"[15].59"[15]1.34" [34]R .67[17]R .67[17]A7.87" [200] min.27.55"[700]3X85681312X#6 X 10AB12.7 mm 19.8 mmCD231Packaging includes: Lift Assembly, CableClamps, Edge Protector, Wire Grommet, WeightPack, Fasteners, Technical Sheet, Quick InstallGuide, and User's GuideMinimum Inside Cabinet DimensionsWidth: 8.0" [200 mm]Height: 28.5" [720 mm] Overlay Lid27.6" [700 mm] Split LidDepth: Dimension Determined by componentsNoTe: The minimum dimensions do not take into consideration theadditional cabinet space required for screen width or depth.Be sure to provide adequate clearance.Cabinet Preparation2.0"[50]13.78"[350]4 Wiring AccessDrill access hole for wiring.Lift InstallationLocate cabinet centerline. Mark and pre-drill mounting holes. Install six #6 X 10screws.Bracket InstallationInstall television/screenmounting bracket(not included). See thebracket kit technical sheetfor detailed installationinstructions and orderinginformation..78"[20].78"[20]Television/Screen InstallationInstall television/screen to mountingbracket (Not included. See the bracket kittechnical sheet for instructions). Noteminimum clearance dimensions forcabinet lids.7910Install the edge protector.Weight plates are installed to counterbalance the weight of thetelevision/screen.If more than two weight packs are required, order the WeightExtension Plate Kit (P/N 2990-9775-BE). See the technicalsheet for weight pack recommendations and orderinginformation.Important: Inadequate weight may cause the unit to lift tooquickly. Too much weight will override the spring-action move-ment.NO FIXED TILTBRACKET BRACKET BRACKETMinimum Weight 6.61 lbs. 5.73 lbs. 5.51 lbs.Maximum Weight 14.5 lbs. 14.5 lbs. 14.5 lbs.Counterbalance WeightsSplit LidAdjust weights by adding or removing one plate at a time tocontrol movement. Fully close the lift and then press to releaseto test the counterbalancing.Installing Weights11Lower the lift to the mid travel pointto expose the final two mountingholes. Install last 2 screws and secure.CB LIFT0019Overlay Lid2XM5 X 12WiringRoute cables through wiring access hole in cabinet,through cable clamp, to the top of the column andto the back of the screen. Adjust slack and secureclamp.2X#6 X 104XM4 X 8

/ 2

Related manuals for Accuride Ascent CB LIFT0019