Accurex XB Installation, Operation And Maintenance Manual

Also see for XB: Installation, operation and maintenance manual

Accurex XB Installation, Operation And Maintenance Manual Manual pdf 8 page image

8HANGER BRACKETATTACH HANGING CLIP TOHOOD STANDING SEAM WITHTHE SUPPLIED "C" CLAMPS(OPTIONAL: DRILL AND BOLT A1/4-20 SS BOLT THROUGHTHE CLIP AND HOOD STANDINGSEAM)MSTOP VIEWHOODTOP VIEWSUPPLY PLENUM2 CLIPS ARE NEEDED3 CLIPS ARE NEEDEDFOR PLENUMS > 96"FOR PLENUMS <= 96"THE THIRD CLIP IS LOCATEDIN THE CENTER OF THE PLENUMLENGTHTHREADED RODOPTION #3OPTION #1ON THE END OF THE HOODHANGING CLIP COULD BE 23.5" FROMEND IF THERE IS A UTILITY CABINETOPTION #1OPTION #1OPTION #2UNI-STRUT SUPPLIED BY OTHERSOPTIONAL UTILITY CABINETHANGING CLIPS (OPTION 1),R 3SUPPLIED BY OTHERS11.523.5HOOD STANDING SEAMHANGING CLIP BOLTED TO PLENUM SHELLHANGING CLIPHOOD FRONT"C" CLAMPSUPPLY PLENUM SHELLEND VIEWTHREADED RODHOODHANGING METHODS FOR SUPPLY PLENUMSASP, FSP AND VSPTHREADED RODOPTION #3HANGING CLIPOPTION #1ON THE ENDHANGING CLEND IF THEROPTION #1THE HOOD AND IS MOUNTED TO THE ASPHOOD UP CANTILEVERS OVER THE END OFTHE UNI-STRUT (U-CHANNEL) THAT HOLDS THEHANGER BRACKETSOPTION #2OPTION #1 = HANGING CLIPOPTION #2 = UNI-STRUTOPTION #3 = THREADED RODNOTE: SUPPLY PLENUMS ARE STANDARDLY SUPPLIED WITH HANGING CLIPS (OPIF OPTION #1 IS NOT APPLICABLE, USE OPTIONS 2 0R 3SUPPLIED BY OTHERSSUPPLY PLENUM SHELLHOOD FRONTHANGING CLIP2.1201.000 147.0°57.4°1.0001.000Form Down 147°Form Up 57°1.3752.1251.0003.0000.5630.5630.7500.7504.500.500 x .375SLOT (3 PLACES)0.6251.5000.625Supply Plenum ClipUsing the Uni-strut1. The uni-strut (supplied by others) that holdsthe hood up cantilevers over the end of thehood and is mounted to the supply plenumhanger brackets.HOOD STANDING SEAMHANGING CLIP BOLTED TO PLENUM SHELLHANGING CLIPHOOD FRONT"C" CLAMPSUPPLY PLENUM SHELLHANGER BRACKETEND VIEWTHREADED RODHOODATTACH HANGING CLIP TOHOOD STANDING SEAM WITHTHE SUPPLIED "C" CLAMPS(OPTIONAL: DRILL AND BOLT A1/4-20 SS BOLT THROUGHTHE CLIP AND HOOD STANDINGSEAM)HANGING METHODS FOR SUPPLY PLENUMSASP, FSP AND VSPTOP VIEWHOODTOP VIEWSUPPLY PLENUM2 CLIPS ARE NEEDED3 CLIPS ARE NEEDEDFOR PLENUMS > 96"FOR PLENUMS <= 96"THE THIRD CLIP IS LOCATEDIN THE CENTER OF THE PLENUMLENGTHTHREADED RODOPTION #3HANGING CLIPOPTION #1OPTION #1ON THE END OF THE HOODHANGING CLIP COULD BE 23.5" FROMEND IF THERE IS A UTILITY CABINETOPTION #1OPTION #1THE HOOD AND IS MOUNTED TO THE ASPHOOD UP CANTILEVERS OVER THE END OFTHE UNI-STRUT (U-CHANNEL) THAT HOLDS THEHANGER BRACKETSOPTION #2OPTION #2UNI-STRUT SUPPLIED BY OTHERSOPTION #1 = HANGING CLIPOPTION #2 = UNI-STRUTOPTION #3 = THREADED RODOPTIONAL UTILITY CABINETSUPPLIED BY OTHERS11.523.5Installing External Supply PlenumsFig. 6Fig. 7Fig. 8Using the Supply Plenum ClipNote: The supply plenum is provided withplenum clips that assist in hanging the plenum.The plenum should not be hung only with theplenum clips, threaded rod or uni-strut mustalso be used.1. Bolt the hanging clip to the supply plenum.Two clips are needed for plenums less than96 in. (43.84 cm) long and three for plenumsgreater than 96 in. (43.84 cm). The third clipis located in the center of the plenum length.If there is a utility cabinet, the hanging clipshould be 3.5 in. (59.69 cm) from the end tothe hood.. Using the c-clamps provided, clamp thesupply plenum hanging clip to the hoodstanding seam. Option: Drill and bolt a1/4-0 SS bolt through the clip and hoodstanding seam.