Abus A-H1 Instruction Manual

Abus A-H1 Instruction Manual Manual pdf 1 page image

Model A-H1Audio Interface Hubfor A-BUS® SystemInstruction ManualINSTRUCTIONS FOR CONNECTING AND USING RUSSOUND® MODEL A-H1. REFER TO THE DIAGRAMS INSIDE. A-H1 OVERVIEWThe A-H1 is an A-BUS Audio Interface Hub that provides an inter-face for audio, status, voltage and infrared between the sourceequipment and the A-H4P A-BUS hub (cannot be used with the A-H4D). The A-H1 can interface a stereo receiver to an A-BUS systemusing the A-H4P.A-H1 KEY FEATURES1) 1 source audio input2) 4 common IR outputs, with confirmation LED3) Status power input with LED indicator4) Main Power LED indicator5) Compact size for mounting near audio equipmentAlthough the A-H1 has only 1 audio input, it can be connected tomultiple audio sources via the Tape 2 or Zone 2 output of a stereo orhome theater receiver. Connecting to a receiver gives the A-H1 accessto any audio source connected to that receiver. Alternately, a singleaudio source can be connected directly to the A-H1.Mount the A-H1 using screws or hook and loop fastener. Securelymount the A-H1 within 6 feet of source equipment.28-1147Connect an IR emitter such as the 845.1 to each of the 4 IR con-nectors on the A-H1 (you need use only one IR emitter if you’veconnected a single source directly to the A-H1). The IR signal thatis received through a zone’s Amplified Keypad is routed to theA-H1’s Common IR outputs. This allows remote operation ofsources such as CD, DVD, or DSS from each zone.SOURCEIR EMITTERSA-H1 CONNECTIONSMOUNTINGA-BUS® SYSTEM OVERVIEWThe product you have just purchased is an integral part of the Russound®A-BUS Multi-Room Audio System. It is a component which, when combinedwith other essential components and your source equipment (receiver, CD play-er, etc.), creates a versatile whole-house audio system that will fill your roomswith high-quality sound for years to come.A-BUS technology is a new, innovative method of providing high quality audioto remote locations with a single 8-conductor cable such as CAT-5. A-BUStechnology provides many advantages over other methods of audio distribu-tion, including: simple, single CAT-5 wiring scheme; infrared control of systemcomponents; infrared control of the optional A-KP2 amplified keypad module;and system power status.Every A-BUS System is comprised of components from each of the followingthree areas.1. A-BUS Amplified Modules: The Module contains both the amplifier for theroom’s speakers as well as the control for those speakers. One Moduleshould be used for each room you choose to control. The Russound A-KP2Amplified Keypad (with built-in IR receiver) and A-VC Amplified VolumeControl are examples of A-BUS Amplified Modules.2. A-BUS Hubs: All components of the A-BUS system must be wired centrallyto a Hub located near your source equipment. The Hub provides the con-nection for source equipment, volume controls, infrared emitters and powersupply. The A-H484, A-H4, A-H4P, and A-H2 are examples of A-BUS Hubs.3. Power Supply: The power supply plugs into the Hub. The Russound A-PS24VDC/2.5A unit is an example.A-H1 SPECIFICATIONSStatus Power: 12VDC/100mA 2.5mm plugInput: 600 ohm line-level audio (RCA)Output: A-BUS ready RJ-45 T568A StandardEmitter Connections: 1/8" Male, Tip (+), sleeve (–)Dimensions: 6.5"W x 2"H x 1.55"D (165 x 51 x 39mm)Weight: 9.5 oz. (270g)5 Forbes Rd. Newmarket, NH 03857, USA☎ 603.659.5170 • Fax 603.659.5388e-mail: tech@russound.comCome visit us at:A-BUS® is a registered trademark of LeisureTech Electronics Pty Ltd AustraliaLIMITED WARRANTYThe Russound A-H1 is fully guaranteed for two (2) years from the date of pur-chase against all defects in materials and workmanship. For this warranty toapply, the unit must be installed and used according to its written instructions.During this period, Russound will replace any defective parts and correct anydefect in workmanship without charge for either parts or labor. Accidental dam-age and shipping damage are not considered defects under the terms of thiswarranty. Russound assumes no responsibility for defects resulting from abuse orservicing performed by an agency or person not specifically authorized in writ-ing by Russound. If service is necessary, it must be performed by Russound.Damage to or destruction of components due to excessive power voids the war-ranty. In these cases, the repair will be made at the owner’s expense. To returnfor repairs, the unit must be shipped to Russound at the owner’s expense, alongwith a note explaining the nature of the service required. Be sure to pack in acorrugated container with at least 3 inches of resilient material to protect theunit from damage in transit.Before returning a unit for repair, call Russound at (603) 659-5170 for a ReturnAuthorization number. Write the RA number on the shipping label and ship to:Russound, ATTN: Service, 5 Forbes Road, Newmarket NH 03857Russound sells product only through authorized Dealers and Distributors toensure that customers obtain proper support and service. Any Russound productpurchased from an unauthorized dealer or other source, including retailers, mailorder sellers and online sellers will not be honored or serviced under existingRussound warranty policy. Any sale of products by an unauthorized source orother manner not authorized by Russound shall void the warranty on the appli-cable product.Note: When making all connections, be sure that the power supplyis not connected.The A-H1 must be connected to the Link In connector on theA-H4P or other A-BUS ready product or hub. Connect the hub out-put to an RJ-45 wall plate. Wire the RJ-45 for the T568A standardusing CAT-5 conductor wire. When using pre-made CAT-5 RJ-45patch cables, be sure they are straight through and do not swapconductor pairs.Run the CAT-5 from the rear of the wall plate to the structuredwiring panel and then to the A-H4P. Use the following color codemarkings to connect the CAT-5 to the Input 110 punchdown con-nector on the A-H4P. (Use a punchdown tool with a 110 blade toinsert conductors).Brown V+Brown/White V-Green L+Green/White L-Orange R+Orange/White R-Blue IRBlue/White StatusRun the CAT-5 from each of the A-BUS keypad modules to thestructured wiring panel. Follow the above color code and punchdown the CAT-5 for each keypad output 110 punchdownconnector.After all of the punchdown connections are made, route the cablesin the box so they avoid power lines and are not grouped withother cables in the panel.POWER - The Power LED will be illuminated when the 24VDCpower supply attached to the A-H4P is on.STATUS INDICATOR - The Status Indicator will be illuminated when12VDC is present at the Status Input connector, indicating thesource equipment is on.IR - The red LED will flash when IR signals are received by theA-BUS keypads. This is used to confirm IR reception from theA-H4P.INDICATORSSTATUS SWITCHThe status feature provides two functions:- Visually confirms when the source component is on.- When the source component is turned off, all Amplified Moduleswill also turn off.The status feature requires that the source component has aswitched AC outlet.To enable the status feature:- Move the status jumper on all Amplified Modules to the“Enabled” position.- Move the status switch on the Hub to the “STATUS” position.- Using a Russound Model 846C 120V/12VDC or comparableadapter, connect the coaxial plug end to the STATUS input onthe Hub, and plug the adapter into a switched AC outlet on thesource component.When the source is on and supplying status voltage to the Hub, theAmplified Module’s LED indicator will illuminate green. When thesource is turned off, all Amplified Modules that are on will alsoturn off (the A-VC will mute).IMPORTANT: When the status feature is enabled, it must be used(i.e., supplied with power) in order to ensure proper operation withaccessories such as the A-LC2 Local Source Input Module.

/ 2

Related manuals for Abus A-H1