Absolute Process Instruments IsoSplitter APD 4930 Quick Start Manual

Absolute Process Instruments IsoSplitter APD 4930 Quick Start Manual Manual pdf 1 page image

Options—add to end of model numberM19 Channel 1 high voltage output (>10 to 20 VDC max.)M29 Channel 2 high voltage output (>10 to 20 VDC max.)M39 Channel 1 and channel 2 high voltage output (>10 to20 VDC max.)EXT1 Sinking mA output channel 1EXT2 Sinking mA output channel 2EXT3 Sinking mA output channel 1 and 2U Conformal coating for moisture resistanceAccessory—order as separate line itemAPI BP4 Spare 4-terminal plug, blackModel Input Output PowerAPD 4930 Factory configuredspecify input range and typeFactory configuredspecify output ranges and type forchannel 1 and channel 285-265 VAC or 60-300 VDCAPD 4930 D 9-30 VDC or 10-32 VACDescriptionThe APD 4930 IsoSplitter accepts a DC voltage or currentinput and provides two optically isolated DC voltage or currentoutputs that are linearly related to the input. The input rangeand each output range are independent and can be specified asrequired. This provides an economical solution when one signalmust be sent to two different devices.Typical applications include isolation, output splitting, outputdevice separation and redundancy (i.e. to prevent failure ofthe entire loop if one device fails), or a combination of these.The input signal is filtered, amplified, split, and then passedthrough an opto-coupler to the output stages. Full 4-way isola-tion (input, output 1, output 2, power) make this module usefulfor ground loop elimination, common mode signal rejection,and noise pickup reduction.Independent OutputsEach output channel is factory ranged to your specificationsand provides an optically isolated DC voltage or current outputthat is linearly related to the input. Sourcing mA outputs arestandard. Sinking milliamp or high voltage outputs are optional.IsolationThe full 4-way (input, output 1, output 2, power) isolationmakes this module useful for ground loop elimination, commonmode signal rejection or noise pickup reduction.LoopTrackerAPI exclusive features include two LoopTracker LEDs (one foreach output channel) that vary in intensity with changes in theprocess output signals. These provide a quick visual picture ofyour process loop at all times and can greatly aid in saving timeduring initial startup and/or troubleshooting.DC Input RangeFactory configured, please specify input range or consult fac-tory for special ranges.Voltage: 0-100 mVDC to 0-300 VDCBipolar voltage: ±100 mVDC to ±10 VDCCurrent: 0-1 mADC to 0-1000 mADCInput Impedance and BurdenVoltage: 200 kΩ minimumCurrent: 50 Ω typicalVoltage burden: 1.25 VDC max. at 20 mA current inputInput Loop Power Supply15 VDC ±10%, regulated, 25 mADCMay be selectively wired for sinking or sourcing mA inputLoopTrackerVariable brightness LEDs indicate output loop level and statusOne red LED for each outputChannel 1 and Channel 2 DC Output RangesFactory configured, please specify for each output channelOutputs are independent and do not need to be the sameVoltage: 0-1 VDC to 0-10 VDC, 10 mA maxUp to 20 VDC with M19, M29, M39Bipolar voltage: ±1 VDC to ±10 VDCCurrent: 0-1 mADC to 0-20 mADC, 4-20 mADC20 V compliance, 1000 Ω at 20 mAOutput CalibrationMulti-turn zero and span potentiometers for each output channel±15% of span adjustment range typicalOutput Loop Power Supplies20 VDC nominal, regulated, 25 mADC for each output channelMay be selectively ordered for sinking mA outputOutput Test/Manual OverrideTerminals for customer-supplied external contacts to manu-ally set output levels for each channelOutput test level factory set to 50 % of spanSpecify if special output percentage levels are requiredOutput Ripple and NoiseLess than 10 mVRMS ripple and noiseLinearityBetter than ±0.1% of spanAmbient Temperature Range and Stability–10°C to +60°C operating ambientBetter than ±0.04% of span per °C stabilityResponse Time70 milliseconds nominalIsolationFull 4-way, 1200 VRMS minimumInstallation EnvironmentIP 40, requires installation in panel or enclosure with ade-quate ventilationFor use in Pollution Degree 2 EnvironmentMount vertically (as shown in picture) to a 35 mm DIN railallowing minimum 1" (25 mm) above and below housingvents for air circulationPower85-265 VAC, 50/60 Hz or 60-300 VDC, 6 W maximumD versions: 9-30 VDC or 10-32 VAC 50/60 Hz, 6 W maximumDimensions and Connectors0.89" W x 4.62" H x 4.81" D22.5 mm W x 117 mm H x 122 mm DFour 4-terminal removable connectors, 14 AWG max wire sizeRemovable Plugs2 Output Channels;Voltage or mA withSink or Source OptionsOutput LoopTrackerLEDZero and Span forEach OutputCustom I/O RangesDC Input: Voltage orSink/Source mAIsoSplitter® DC to DC Signal Splitter/Isolator/Transmitter, Factory Configured APD 49301 Input: 0-100 mV to 0-300 V, ±100 mV to ±10 V, 0-1 mA to 0-1000 mA, 4-20 mA2 Outputs: 0-1 V to 0-10 V, optional up to 20 V, ±1 V to ±10 V, 0-1 mA to 20 mA, 4-20 mAO One Input to Two Outputs with Full IsolationO Zero and Span Output Calibration PotentiometersO Full 1200 V Input/Output /Power IsolationO Output LoopTracker®LEDsO Output Test/Manual Override for Each ChannelO Built-In Loop Power Supply for Sink/Source InputQ Split, Convert, Boost, and Rescale Process SignalsQ Split Process Signals for Control and ValidationQ Interface a Process Signal with Multiple Panel Meters,PLCs, Recorders, Data Acq., DCS, & SCADA SystemsApplications1 2 3 45 6 7 89 10 11 1213 14 15 16See WiringDiagrams onNext Page© 08-20api-usa.com1220 American Way Libertyville, IL 60048Phone: 800-942-0315 Fax: 800-949-7502AABSOLUTEBSOLUTE PPROCESSROCESS IINSTRUMENTSNSTRUMENTSQuick Link: api-usa.com/4930UniversalPowerFree FactoryI/O Setup!H H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HMade in USAApplications Linkapi-usa.com/appsPb LeadFree

/ 2

Related manuals for Absolute Process Instruments IsoSplitter APD 4930