Menu
ADT TSSBU111011U Installation And Setup Manual
  | |
Contents | 
1TSSC Installation and Setup GuideSTEP 1 - Installing the Base (TSSBU111011U) RechargeableBackup Battery and Power Connector1. Remove the Base Case Back.2. Connect the battery connector to the receptacle on the PC board.3. Insert the Battery Pack into the case.4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw.5. Connect the power pack into the power receptacle, looping the power cord asshown in Detail A.NOTE: If using the optional wall mount configuration, skip to the Base wallmounting procedure. If not, complete step 6.6. Secure the Case Back onto the Base.NOTE: Do not apply power at this time.CASEBACKRETAININGSCREWBASE UNITBATTERYRETAINERBATTERYPACKtssc-016-V0DETAIL AMounting the Base to a Wall (Optional)To mount the Base to a wall, perform to the following:IMPORTANT: Record the ACTIVATION KEY number, MAC Address, CRCnumber and WPA2 number located on case back prior to wall mounting.1. Complete steps 1 through 5 of the Installing the Base Rechargeable BackupBattery and Power Connector paragraph2. Secure the Mounting Plate to the wall and secure with 4 screws.3. Install the Tamper Screw as shown.4. Secure the Base to the Mounting Plate by aligning the slots on the Base andsliding the unit down until locked in position.tssc-015-V0ENGAGE HOOKSAND SLIDE DOWN(4)WALLMOUNTINGPLATEWALLSURFACEREAR OFBASE UNITSECURE CASE BACKUSING MOUNTINGSCREWS (TYP - 4 PLACES)TAMPERSCREWBATTERYPACKSTEP 2 - Setting up the Communication LinksPrior to power up of the Base (when directed in the TSSC Installer App), the Ethernetcommunications link must be connected to the residence’s router. The connection is from anEthernet port on the router to the “ETH0” port on the Base.IMPORTANT! Under no circumstances should the “ETH1” port ever be connected to theresidence’s router.tssc-021-V0BASEUNITTO/FROMRESIDENCEROUTERETHERNETPORTFOR INSTALLERUSE ONLYTO POWERRECEPTACLEETH0ETH1STEP 3 - Keypad (TSSKP112011U) MountingThe keypad is designed to be placed on a desk/table top with the stand attached. An optionalmounting plate can be used to mount the keypad to the wall.Power ConnectionsConnect the Power Supply Cable into its connector as shown below and route it from the bottomof the keypad.IMPORTANT: Do not apply power to the keypad at this time.Installing Keypad To Desk-Top Stand1. Place the Keypad face down on a level surface.2. Connect the battery connector to the receptacle on the PC board.3. Insert the Battery Pack into the case.4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw.5. Install tabs on Desk Stand into appropriate slots as shown and secure with two screws6. Plug in the power pack to the receptacle.BATTERYPACKPOWERSUPPLYCABLEKEYPADtssc-011-V1SLIDE TABSUP INTOSLOTSSLOT(TYP)DESKSTANDSECURE WITHSCREWS (2)(TYP)STEP 4 - Base Registration and Accessing The Installer AppRun TSSC Installer App:Go to https://portal-test.adtpulse.com/activation and follow the prompts.Powering the BaseWhen directed in the TSSC Installer App, plug the power pack into the wallreceptacle to power the Base. During the first 45 seconds of power initialization, TSSClights up the CELLULAR, NETWORK and STATUS LEDs one by one slowly in sequence.After the first 45 seconds, the LEDs chase in a rapid sequence for approximately 30 moreseconds. The POWER LED is always ON while initialization is being executed. When theLEDs stop chasing and the POWER LED is lit green, the Base is powered up and readyfor the registration process to begin.NOTE: The BATTERY LED will blink until the battery is fully charged.NOTE: The NETWORK LED will remain amber until activated.Radio ActivationGo to https://portal-test.adtpulse.com/activation and follow the prompts.Ê800-13956V1oŠ800-13956V1 11/13 Rev. AEXHIBIT 7B CFS8DLTSSCBASE / 573F-TSSCBASE |
Related manuals for ADT TSSBU111011U
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved