ADC AD-75V Installation Manual

ADC AD-75V Installation Manual Manual pdf 10 page image

6SECTION IISPECIFICATIONSA. SPECIFICATIONS* AD-75V 50 Hz 1-phase (1ø) non-reversing dryers use a 3/4 hp (0.56 kW) motor. ALL AD-75V reversingdryers are supplied with two (2) 3-phase (3ø) motors standard: a 1 hp (0.746 kW) blower motor and a1/2 hp (0.37 kW) drive motor.** Size of piping to dryer varies with installation conditions. Contact factory for assistance.*** Contact factory for information not listed, 3-phase (3ø) figures shown are for 3-wire service.**** Specify air-operated or electromechanical steam damper system. Air-operated steam damper systemmust be provided with clean, dry, and regulated 80 psi +/- 10 psi (5.51 bar +/- 0.68 bar) air supply.NOTE: ADC reserves the right to make changes in specifications at any time without notice orobligation.STEAM**** GASELECTRICMAXIMUM CAPACITY (DRY WEIGHT) 75 lbs 34 kgBASKET (TUMBLER) DIAMETER 37” 94 cmBASKET (TUMBLER) DEPTH 36” 91.5 cmBASKET (TUMBLER) MOTOR 1 hp* 0.746 kWDOOR OPENING (DIAMETER) 21-1/2” 54.61 cmBASKET (TUMBLER) VOLUME 22.4 cu.ft. 0.634 cu.m.AIRFLOW 900 cfm 25.48 cmmVOLTAGE AVAILABLE 120-460v 1ø-3ø 3, 4w 50/60 HzAPPROX. WEIGHT (UNCRATED) 833 lbs 377.8 kgAPPROX. WEIGHT (CRATED) 883 lbs 400.5 kgHEAT INPUT 200,000 Btuh 50,400 kcal/hrINLET PIPE CONNECTION 3/4” F.N.P.T.**OVEN SIZEkW BTUH(60 HZ )KCAL/HR(50 Hz)30 102,387 25,80236 122,864 30,962APPLIED VOLTAGE/PHASE/APPROX. AMP DRAW***kW 208/1ø 240/1ø 208/3ø 240/3ø 380/3ø 400/3ø 416/3ø 460/3ø 480/3ø60/50 Hz 50/60 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz30 -- -- 87 -- 77 80 -- 54 -- 52 -- 49 40 -- 39 --36 -- -- 105 -- 92 94 -- 63 -- 60 -- 58 48 -- 46 --VOLTAGE AVAILABLE 120-460v 1ø - 3ø 3, 4w 50/60 HzAPPROX. WEIGHT (UNCRATED) 864 lbs 392.7 kgAPPROX. WEIGHT (CRATED) 914 lbs 415.5 kgCOMPRESSED AIR VOLUME 0.75 cfh 0.02 cmhAIR CONNECTION 1/8” F.N.P.T.STEAM CONSUMPTION BOILER HP NORMAL LOAD238.7 lbs/hr 108.3 kg/hr 7OPERATING PRESSURE SUPPLY CONNECTION** RETURN CONNECTION125 psi max 8.6 bar 1” F.N.P.T. 1” F.N.P.T.Shaded areas are stated in metric equivalents 052203