OneStart

Menu

ACS ACD Manual

Also see for SCD: Operation and instruction manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. CHAPTER 1: SAFETY
  4. General Safety Regulations
  5. Warnings and Precautions
  6. CHAPTER 2: FUNCTIONAL DESCRIPTION
  7. Safety Features
  8. Remote Membrane Dryer for Low-Dewpoint Operation (Optional)
  9. Microprocessor Controls
  10. Identifying the Controller's Buttons and Indicators
  11. Understanding the Controller's Parameters
  12. Restoring Factory Default Settings
  13. CHAPTER 3: INSTALLATION
  14. Connecting a Floor-Mount Dryer to a Hopper
  15. Making Electrical Connections
  16. Installing the Remote-Mount Membrane Dryer (Optional)
  17. CHAPTER 4: OPERATION
  18. Start-up
  19. CHAPTER 5: MAINTENANCE
  20. CHAPTER 6: TROUBLESHOOTING
  21. CHAPTER 7: APPENDIX
  22. Technical Specifications
  23. Dryer Operating Parameters
  24. Dimensions
  25. Spare Parts List
  26. technical assistance
ACS ACD Manual Manual pdf 9 page image
Compressed Air Dryer Chapter 2: Functional Description 9 of 31Chapter 2: Functional Description2-1 Models Covered in This ManualThis manual provides instructions for installing and operating your 5, 10 or 15 cfmcompressed air dryer.2-2 General DescriptionMini compressed air dryers are designed to generate heated, dehumidified air at carefullycontrolled temperatures for use in plastic drying systems. Drying systems are sized to meetspecific requirements stated by the purchaser at the time of purchase.Moisture removal from hygroscopic (moisture attracting) plastic pellets is an essential step inthe manufacture of high-quality plastic products. This dehumidifying dryer is used togenerate very low dew point air, heated to a controlled temperature for drying plastic pelletsand regrind.Many variables were considered in the selection of your drying system, including type ofmaterials, residence time, throughput of the extruder or injection molding machine. Shouldyour operating environment change, the manufacturer can advise you on necessary equipmentand process time and temperature modifications required for your system.2-3 Typical Features and Components· Electrical solenoid valve· Compressed air filter, regulator, and gauge· Drying temperature range of 120ºF to 400ºF· Display of process temperature set point and actual settings· Process thermocouple located in the process air stream just before the hopper inlet· Nema 1 control enclosure:a. Fusingb. Power On lightc. IEC process heater contactord. Solid state relaye. Alarm lightf. High temperature safety systemg. Airflow detection system2-4 OptionsOptions can tailor your dryer to meet the exact requirements of the drying task beingperformed.· Floor-mount configuration· Membrane compressed air dryer for low dew point operation· 220/1/50 operation· 230/1/60 operation
/ 31
Related manuals for ACS SCD
ACS 882.02569.00 Mechanical Manual first page preview
ACS 882.02569.00 Mechanical Manual
ACS Sterling MDB Series Reference Manual first page preview
ACS Sterling MDB Series Reference Manual
ACS ADP Series Operation And Instruction Manual first page preview
ACS ADP Series Operation And Instruction Manual
ACS ADC Series Operation And Instruction Manual first page preview
ACS ADC Series Operation And Instruction Manual
This manual is suitable for:
SCD882.03168.00ACD
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved