ACP HDC Y Series Quick Start Manual

ACP HDC Y Series Quick Start Manual Manual pdf 1 page image

©2020 ACP, Inc.Cedar Rapids, IA 52404Part No. 20289100Original InstructionsQuick Start GuideRefer to Owner’s Manual for Safety Statements. Complete Owner’s Manual available online.This document covers HDC*-Y* and MDC*-Y* modelsAIR FILTER INSTALLATIONOven ships with two (2) Air Filters taped to the floor of the oven interior.⚠ Do NOT operate oven without the air filters installed.1. Remove and discard tape.2. Locate air filter in the recessed grills along the base of the left and right sides of the oven.3. Angle the Air Filter with the lower edge placed inside the bottom of the recessed grill.4. Rotate the top of the air filter to snap into place.5. Repeat steps 2-4 for the other side and air filter.(F) Secondary Function KeypadsTo activate, press and hold correspondingnumber keypad.(i) Manual Time Entry Mode (keypad “1”)(ii) Power Level (keypad “2”)(iii) Programming Mode (keypad “3”)(iv) User Options (number keypad “4”)(v) X2 - Double Quantity Cooking (keypad “5”)(vi) Menu A/B (keypad “6”)ABCDADBCSo…how do I use it?Manual Time Entry ModeTime entry mode allows the user to manually enter cook time and power level, withoutchanging the preset program keypads.1. Open oven door, place food in oven, and close door.2. Press and hold number keypad “1”/ TIME ENTRY.3. Press number keypads to enter desired cook time.4. Press and hold number keypad “2”/ POWER LEVEL to change power level.• Press number keypads to enter % microwave power (“1”=10%, “2”=20%,etc.)For 100% power level, press and hold number keypad “2”/ POWER LEVEL.5. Press START/OK keypad to begin cooking.6. At the end of the cooking cycle, the oven beeps. Carefully remove food from oven.Programming Mode1. Press and hold number keypad “3”/ PROGRAM.2. Press number keypad(s) to open the desired program location.3. To edit name: Press number keypad “0”. Press number keypads to enter recipe name.Press START/OK keypad.4. To edit cook time for Stage One: Press number keypad “1”. Press number keypads toenter cook time. Press START/OK keypad.5. To edit power level for Stage One: Press number keypad “5”. Press number keypads toenter % microwave power (“1”=10%, “2”=20%,etc.). For 100% power level, press and holdnumber keypad “2”/ POWER LEVEL.6. If stage cooking is desired, repeat steps 4-5 for each additional stage, substitutingcorresponding number keypads for each stage.7. To save and exit programming mode: Press START/OK keypad.OVEN CLEARANCESA. Allow at least 2” (5.1 cm) of clearancearound top of oven. Proper air flow aroundoven cools electrical components. Withrestricted air flow, oven may not operateproperly and life of electrical parts isreduced.B. There is not an installation clearancerequirement for the back of the oven.C. Allow at least 1” (2.54 cm) of clearancearound sides of oven.D. Install oven so oven bottom is at least3 feet (91.5 cm) above floor.(C)(F)(i)(B) (D) (E)(ii) (iii) (iv) (v) (vi)(A)CONTROL PANEL FEATURES(A) USB Port(B) Display(C) Number Keypads(D) Start/ OK Keypad(E) Stop/ Reset Keypad23Air FiltersPreset Program KeypadsTo cook food using preprogrammed cookingsequences:1. Open oven door, place food in oven, andclose oven door.2. Press desired number keypad(s).3. Oven operates and time counts down.4. At the end of the cooking cycle, the ovenbeeps. Carefully remove food from oven.X2 - DOUBLE QUANTITY COOKING1. Press and hold number keypad “5”/ X2 totoggle double quantity feature ON.“X2” appears at top center of screenwhen enabled.2. Press desired number keypad(s).Display counts down cooking time fortwo quantities.MENU A/B (select models)Press and hold number keypad “6” to togglebetween A and B menus.4

/ 2

Related manuals for ACP HDC Y Series