ACME IM-5S-ELC User Manual

Also see for IM-5S-ELC: User guide

Contents

ACME IM-5S-ELC User Manual Manual pdf 19 page image

9J4.2 Main FunctionTo select any of the given functions, press the MENU button up to when the required one isshowing on the display. Select the function by ENTER button and the display will blink. UseDOWN and UP button to change the mode. Once the required mode has been selected,press the ENTER button to setup or it will automatically return to the main functions withoutany change after idling 8 seconds. To go back to the functions without any change press theMENU button. The main functions are showing below:MENUFocus AdjustSelf-TestResetFixture HoursDisplay InversionDisplay NormalTilt InversionTilt NormalPan InversionPan NormalSplit ColorNormal ColorShow mode 4Show mode 3DMX512 Address SettingBlackout Mode " No Blackout "Blackout Mode " Yes Blackout "Slave Mode " Normal "Slave mode " 2 Light Show "Show mode 1Show mode 2LED offLED onDimmer NormalDimmer InversionDMX 512 Address SettingPress the MENU button up to when the is showing on the display. Pressing ENTERbutton and the display will blink. Use DOWN and UP button to change the DMX512 address.Once the address has been selected, press the ENTER button to setup or automaticallyreturn to the main functions without any change after 8 seconds. To go back to the functionswithout any change press the MENU button again.14JStand by Blackout the unitFunctionStrobe1.Gobo / Colorsync.strobe2.Sync. strobe3.Two-light strobeX/Y moving showmode selection( Show 1 ~ Show4 )Please refer toShow mode in4.2 Main FunctionColor/Goboselection1. Hold on for gobochange.2. Press shortly forcolor changeX/Y moving setting1.Pan position2.Tilt positionFirst set Masterunit, then set Slaveunits’ positionMoveSpotModeSound 1(LED off )Sound 2(LED normalblinking)Slow/Sound 3(LED on)Position/ Latch(LED fast blinking)Stand by Blackout the unitFunctionStrobe1.Color sync.strobe2.Sync. strobe3.Two-light strobeX/Y moving showmode selection( Show 1 ~ Show4 )Please refer toShow mode in4.2 Main FunctionColor selection X/Y moving setting1.Pan position2.Tilt position3.DimmerFirst set Masterunit, then set Slaveunits’ positionMoveWashModeSound 1(LED off )Sound 2(LED normalblinking)Slow/Sound 3(LED on)Position/ Latch(LED fast blinking)5.3.1 iSolution Operation♦ Consistent DMX configuration enable iMove to be linked together with iRock and iShowand controlled at the same time.♦ DMX address can be set remotely by iLead controller ( please refer to the user manual ofiLead controller ). No need to calculate the DMX channels of each fixture in the chain.♦ Automatic switching between DMX function and built-in stand alone programs.5.3.2 DMX ControllerAn universal DMX controller to control the units, you have to set DMX address from1 to 512 channel so that the units can receive DMX signal.Press the MENU button up to when the is showing on the display. Pressing ENTERbutton and the display will blink. Use DOWN and UP button to change the DMX512 address.Once the address has been selected, press and keep ENTER button pressed up to whenthe display stops blinking or storing automatically 8 seconds later. To go back to thefunctions without any change press the MENU button again. If you use please refer to thefollowing diagram to address your DMX512 channel for the first 4 units.DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMXchannels of each fixture in the chain.