AC Pro AUHD24ND3F1O Service Manual

Also see for AFH18D3F3I: User manual

Contents

AC Pro AUHD24ND3F1O Service Manual Manual pdf 12 page image

10(4) Heavy pollution: the former digit in timer zone shows 3 while the latter one shows 0, which indicatesthe accumulated operating time is 100hr. Each time the latter digit increases 1, the accumulated operating time increases 100hr. When it reaches 9, it means the accumulated operating time is 1000hr;The detailed pollution level and the corresponding time is as shown in Table 2-4-1 below:If filter clean reminder function is turned on, the icon will be on.(1) If cleaning time is not reached, no mater the setting is changed or not, the accumulated operating timewon’t be recalculated when pressing Enter/Cancel button;(2) If cleaning time is reached, in unit on or off state, will blink every 0.5s for reminder. Press Functionbutton to switch to icon and press and button to adjust the level. Then press Enter/Cancelbutton, so the accumulated operating time won’t be cleared (If the adjusted level is higher than thepresent accumulated operating time, the icon won’t blink any more; if the adjusted level is lower than thepresent accumulated operating time, the icon will go on blinking).(3) The only way to cancel filter clean reminder function is to press Function button to switch to filter cleanreminder function. The icon will blink and press or button to adjust timer zone to display“00”. In this case, the accumulated operating time will be cleared.Under dry mode and when set temperature is 61 F, continuously press button for twice and then the set tem-perature will be 54 F. In this case, the unit will enter low temperature drying function.When low temperature drying function is turned on, press button or Mode button to exit low temperaturedrying function.When unit is turned on normally or turned off, pressing and buttons at the same time for 5s will turn onLock function. LCD will display . Pressing and buttons at the same time for 5s to turn off this function.When Lock function is turned on, any other buttons won’t respond when pressing. The function can be memo-rized after power failure and then power recovery.Table 2-4-1 Pollution level and corresponding timePollution levelAccumulatedoperating time(hour)Pollution levelAccumulatedoperating time(hour)Pollution levelAccumulatedoperating time(hour)10 5500 20 1400 30 10011 6000 21 1800 31 20012 6500 22 2200 32 30013 7000 23 2600 33 40014 7500 24 3000 34 50015 8000 25 3400 35 60016 8500 26 3800 36 70017 9000 27 4200 37 80018 9500 28 4600 38 90019 10000 29 5000 39 100023master/slave wired controller‟s addressCTION OF SPECIALer Functionch to filter clean reminder function. The icon willunction. Time r zone displays the set pollution level anden press Enter/Cancel button to turn on this function.d on, press Function button to switch to filter cleanss ▲ or ▼ button to adjust timer zone to display “00”.ion.ster/slave wired controller‟s addressTION OF SPECIALr Functionto filter clean reminder function. The icon willtion. Time r zone displays the set pollution level andpress Enter/Cancel button to turn on this function.on, press Function button to switch to filter clean▲ or ▼ button to adjust timer zone to display “00”..23y and setting of master/slave wired controller‟s addressSTRUCTION OF SPECIALan Reminder Functionbutton to switch to filter clean reminder function. The icon willlean reminder function. Time r zone displays the set pollution level andjust the level. Then press Enter/Cancel button to turn on this function.nction is turned on, press Function button to switch to filter cleanill blink and press ▲ or ▼ button to adjust timer zone to display “00”.ancel this function.23-5 Enquiry and setting of master/slave wired controller‟s addressN INSTRUCTION OF SPECIALr Clean Reminder FunctionFunction button to switch to filter clean reminder function. The icon willof filter clean reminder function. Time r zone displays the set pollution level andton to adjust the level. Then press Enter/Cancel button to turn on this function.inder function is turned on, press Function button to switch to filter cleanicon will blink and press ▲ or ▼ button to adjust timer zone to display “00”.utton to cancel this function.U-Match Series DC Inverter Service Manual213.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wired controllerNo. Description Functions1 Enter/Cancel①. Function selection and canceling;②. Press it for 5s to view the ambient temperaturto select viewing outdoor ambient temperatutemperature.2 ▲①. Running temperature setting range16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving temperature;⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/medium low/lo4 Mode Setting of auto/cooling/heating/fan/dry mode of indo5 Function Switch over among these functions of swing/air/sleeI-Demand/out/turbo/save/e-heater/X-fan/clean/quiet7 Timer Timer setting.8 On/Off Turn on/off indoor unit.4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the same time for 5sunit to enter/cancel memory function (If memory funit will resume original setting state after power farecovery. If not, indoor unit is defaulted to be offEx-factory setting of memory function is on).2 ▲and6 ▼LockUpon startup of the unit without malfunction or undepress ▲ and ▼ buttons at the same time for 5s to ecase, any other buttons won‟t respond when pressinbuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Mode and Functiotime for 5s to set the address. (More details pledebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer tothe Notes)Under off state of the unit, press Function and Timetime for 5s to go to the debugging menu. Press Modsetting items and press ▲ or ▼ buttons to set the a4 Modeand6 ▼Switch betweenFahrenheit andCentigradeUnder off state of the unit, press Mode and ▼ buttfor 5s to switch between Fahrenheit and Centigrade5 Functionand6 ▼Viewing historicalmalfunctionContinuously press Function and ▼ buttons formalfunction. Then press ▲ and ▼ buttons to adjusThe timer displaying position displays the sequencthe detailed error code. The 5th displayed mamalfunction.1 Enter/Canceland4 ModeSetting of masterand slave wiredcontrollerUnder off state of the unit, press Enter/Cancel andsame time for 5s to set master and slave wired conbutton to adjust. (More details please refer to projecU-Match Series DC Inverter Service Manual3.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wired controlleNo. Description Functions1 Enter/Cancel①. Function selection and canceling;②. Press it for 5s to view the ambient tempto select viewing outdoor ambient temtemperature.2 ▲①. Running temperature setting ra16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving temperature;⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/medium4 Mode Setting of auto/cooling/heating/fan/dry mode o5 Function Switch over among these functions of swing/aI-Demand/out/turbo/save/e-heater/X-fan/clean7 Timer Timer setting.8 On/Off Turn on/off indoor un4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the same timeunit to enter/cancel memory function (If memunit will resume original setting state after porecovery. If not, indoor unit is defaulted to bEx-factory setting of memory function is on).2 ▲and6 ▼LockUpon startup of the unit without malfunction opress ▲ and ▼ buttons at the same time for 5case, any other buttons won‟t respond when pbuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Mode and Futime for 5s to set the address. (More detadebugging)Setting of projectU-Match Series DC Inverter Service Manual3.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wired controllerNo. Description Functions1 Enter/Cancel①. Function selection and canceling;②. Press it for 5s to view the ambient temperature; pto select viewing outdoor ambient temperaturetemperature.2 ▲①. Running temperature setting range o16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving temperature;⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/medium low/low/a4 Mode Setting of auto/cooling/heating/fan/dry mode of indoor5 Function Switch over among these functions of swing/air/sleep/hI-Demand/out/turbo/save/e-heater/X-fan/clean/quiet.7 Timer Timer setting.8 On/Off Turn on/off indoor unit.4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the same time for 5s ununit to enter/cancel memory function (If memory funcunit will resume original setting state after power failurecovery. If not, indoor unit is defaulted to be off afteEx-factory setting of memory function is on).2 ▲and6 ▼LockUpon startup of the unit without malfunction or under opress ▲ and ▼ buttons at the same time for 5s to entecase, any other buttons won‟t respond when pressing.buttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Mode and Function butime for 5s to set the address. (More details pleasdebugging)U-Match Series DC Inverter Service Manual3.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wired coNo. Description Functi1 Enter/Cancel①. Function selection and canceling②. Press it for 5s to view the ambieto select viewing outdoor ambietemperature.2 ▲①. Running temperature settin16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving tempera⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/m4 Mode Setting of auto/cooling/heating/fan/dry5 Function Switch over among these functions ofI-Demand/out/turbo/save/e-heater/X-fa7 Timer Timer setting.8 On/Off Turn on/off in4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the samunit to enter/cancel memory functionunit will resume original setting staterecovery. If not, indoor unit is defaultEx-factory setting of memory function2 ▲and6 ▼LockUpon startup of the unit without malfunpress ▲ and ▼ buttons at the same timcase, any other buttons won‟t respondbuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Modetime for 5s to set the address. (Modebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer tothe Notes)Under off state of the unit, press Functime for 5s to go to the debugging mensetting items and press ▲ or ▼ button4 Modeand6 ▼Switch betweenFahrenheit andCentigradeUnder off state of the unit, press Modfor 5s to switch between Fahrenheit an5 Functionand6 ▼Viewing historicalmalfunctionContinuously press Function and ▼malfunction. Then press ▲ and ▼ buThe timer displaying position displaysthe detailed error code. The 5th dmalfunction.1 Enter/Cancel Setting of master Under off state of the unit, press EnteU-Match Series DC Inverter Service Manual3.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wired contrNo. Description Functions1 Enter/Cancel①. Function selection and canceling;②. Press it for 5s to view the ambient teto select viewing outdoor ambienttemperature.2 ▲①. Running temperature setting16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving temperature⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/med4 Mode Setting of auto/cooling/heating/fan/dry mo5 Function Switch over among these functions of swiI-Demand/out/turbo/save/e-heater/X-fan/c7 Timer Timer setting.8 On/Off Turn on/off indoo4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the same tiunit to enter/cancel memory function (Ifunit will resume original setting state afterecovery. If not, indoor unit is defaultedEx-factory setting of memory function is o2 ▲and6 ▼LockUpon startup of the unit without malfunctiopress ▲ and ▼ buttons at the same time fcase, any other buttons won‟t respond whbuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Mode antime for 5s to set the address. (Moredebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer tothe Notes)Under off state of the unit, press Functiontime for 5s to go to the debugging menu. Psetting items and press ▲ or ▼ buttons to4 ModeandSwitch betweenFahrenheit and Under off state of the unit, press Mode an21Table 2-3-2 Instruction to buttons of wired controNo. Description Functions1 Enter/Cancel①. Function selection and canceling;②. Press it for 5s to view the ambient teto select viewing outdoor ambient ttemperature.2 ▲①. Running temperature setting16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving temperature⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/medi4 Mode Setting of auto/cooling/heating/fan/dry mod5 Function Switch over among these functions of swinI-Demand/out/turbo/save/e-heater/X-fan/cl7 Timer Timer setting.8 On/Off Turn on/off indoo4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the same timunit to enter/cancel memory function (If munit will resume original setting state afterrecovery. If not, indoor unit is defaulted tEx-factory setting of memory function is on2 ▲and6 ▼LockUpon startup of the unit without malfunctiopress ▲ and ▼ buttons at the same time focase, any other buttons won‟t respond whebuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Mode andtime for 5s to set the address. (More ddebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer tothe Notes)Under off state of the unit, press Functiontime for 5s to go to the debugging menu. Psetting items and press ▲ or ▼ buttons to4 Modeand6 ▼Switch betweenFahrenheit andCentigradeUnder off state of the unit, press Mode anfor 5s to switch between Fahrenheit and C5 Functionand6 ▼Viewing historicalmalfunctionContinuously press Function and ▼ butmalfunction. Then press ▲ and ▼ buttonsThe timer displaying position displays thethe detailed error code. The 5th displmalfunction.1 Enter/Canceland4 ModeSetting of masterand slave wiredcontrollerUnder off state of the unit, press Enter/Casame time for 5s to set master and slave wbutton to adjust. (More details please referU-Match Series DC Inverter Service Manual3.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wired coNo. Description Functi1 Enter/Cancel①. Function selection and canceling②. Press it for 5s to view the ambieto select viewing outdoor ambietemperature.2 ▲①. Running temperature settin16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving tempera⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/m4 Mode Setting of auto/cooling/heating/fan/dry5 Function Switch over among these functions ofI-Demand/out/turbo/save/e-heater/X-f7 Timer Timer setting.8 On/Off Turn on/off in4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the samunit to enter/cancel memory functionunit will resume original setting staterecovery. If not, indoor unit is defaulEx-factory setting of memory function2 ▲and6 ▼LockUpon startup of the unit without malfupress ▲ and ▼ buttons at the same ticase, any other buttons won‟t respondbuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Modetime for 5s to set the address. (Modebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer tothe Notes)Under off state of the unit, press Functime for 5s to go to the debugging mensetting items and press ▲ or ▼ buttonU-Match Series DC Inverter Service Manual3.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wired controllerNo. Description Functions1 Enter/Cancel①. Function selection and canceling;②. Press it for 5s to view the ambient tempeto select viewing outdoor ambient tempetemperature.2 ▲①. Running temperature setting ran16~30℃(61~86℉);②. Timer setting range: 0.5~24hr;③. Setting of air function level;④. Setting of energy-saving temperature;⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/medium/medium lo4 Mode Setting of auto/cooling/heating/fan/dry mode of5 Function Switch over among these functions of swing/airI-Demand/out/turbo/save/e-heater/X-fan/clean/7 Timer Timer setting.8 On/Off Turn on/off indoor unit4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at the same time founit to enter/cancel memory function (If memounit will resume original setting state after powrecovery. If not, indoor unit is defaulted to beEx-factory setting of memory function is on).2 ▲and6 ▼LockUpon startup of the unit without malfunction orpress ▲ and ▼ buttons at the same time for 5scase, any other buttons won‟t respond when prbuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, press Mode and Funtime for 5s to set the address. (More detaildebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer toUnder off state of the unit, press Function andtime for 5s to go to the debugging menu. Presssetting items and press ▲ or ▼ buttons to set tU-Match Series DC Inverter Service Manual213.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons of wNo. Description1 Enter/Cancel①. Function selection and can②. Press it for 5s to view theto select viewing outdoortemperature.2 ▲①. Running temperature16~30℃(61~86℉);②. Timer setting range: 0.5~2③. Setting of air function leve④. Setting of energy-saving te⑤. Setting of cleaning class.6 ▼3 Fan Setting of high/medium high/me4 Mode Setting of auto/cooling/heating/5 Function Switch over among these functI-Demand/out/turbo/save/e-hea7 Timer Timer setting.8 On/Off Turn o4 Modeand2 ▲Memory functionPress Mode and ▲ buttons at tunit to enter/cancel memory fuunit will resume original settingrecovery. If not, indoor unit isEx-factory setting of memory fu2 ▲and6 ▼LockUpon startup of the unit withoupress ▲ and ▼ buttons at the scase, any other buttons won‟t rebuttons for 5s to quit lock state.4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, prestime for 5s to set the addresdebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer tothe Notes)Under off state of the unit, prestime for 5s to go to the debuggisetting items and press ▲ or ▼4 Modeand6 ▼Switch betweenFahrenheit andCentigradeUnder off state of the unit, presfor 5s to switch between Fahren5 Functionand6 ▼Viewing historicalmalfunctionContinuously press Function amalfunction. Then press ▲ andThe timer displaying position dthe detailed error code. Themalfunction.1 Enter/Canceland4 ModeSetting of masterand slave wiredcontrollerUnder off state of the unit, presame time for 5s to set masterbutton to adjust. (More details pU-Match Series DC Inverter Service Manual3.3.2 Instruction to Function of ButtonsTable 2-3-2 Instruction to buttons ofNo. Description1 Enter/Cancel①. Function selection and②. Press it for 5s to view tto select viewing outdotemperature.2 ▲①. Running temperature16~30℃(61~86℉);②. Timer setting range: 0.5③. Setting of air function le④. Setting of energy-saving⑤. Setting of cleaning clas6 ▼3 Fan Setting of high/medium high/4 Mode Setting of auto/cooling/heatin5 Function Switch over among these funI-Demand/out/turbo/save/e-h7 Timer Timer setting.8 On/Off Tur4 Modeand2 ▲Memory functionPress Mode and ▲ buttons aunit to enter/cancel memoryunit will resume original settrecovery. If not, indoor unitEx-factory setting of memory2 ▲and6 ▼LockUpon startup of the unit withpress ▲ and ▼ buttons at thcase, any other buttons won‟buttons for 5s to quit lock sta4 Modeand5 FunctionEnquiry andsetting of addressof wiredcontrollerUnder off state of the unit, prtime for 5s to set the addrdebugging)5 Functionand7 TimerSetting of projectparameters(More detailsplease refer tothe Notes)Under off state of the unit, prtime for 5s to go to the debugsetting items and press ▲ or4 Modeand6 ▼Switch betweenFahrenheit andCentigradeUnder off state of the unit, pfor 5s to switch between Fah5 Functionand6 ▼Viewing historicalmalfunctionContinuously press Functiomalfunction. Then press ▲ aThe timer displaying positionthe detailed error code. Tmalfunction.3.2 Low Temperature Drying Function3.3 Lock Function25accumulated operating time increases 400hr. When it reaches 9, it means the accumulatedoperating time is 5000hr;(4) Heavy pollution: the former digit in timer zone shows 3 while the latter one shows 0, whichindicates the accumulated operating time is 100hr. Each time the latter digit increases 1, theaccumulated operating time increases 100hr. When it reaches 9, it means the accumulatedoperating time is 1000hr;The detailed pollution level and the corresponding time is as shown in Table 2-4-1 below:Table 2-4-1 Pollution level and corresponding timePollutionlevelAccumulatedoperating time(hour)PollutionlevelAccumulatedoperating time(hour)PollutionlevelAccumulatedoperating time(hour)10 5500 20 1400 30 10011 6000 21 1800 31 20012 6500 22 2200 32 30013 7000 23 2600 33 40014 7500 24 3000 34 50015 8000 25 3400 35 60016 8500 26 3800 36 70017 9000 27 4200 37 80018 9500 28 4600 38 90019 10000 29 5000 39 1000If filter clean reminder function is turned on, the icon will be on.(1) If cleaning time is not reached, no mater the setting is changed or not, the accumulated operatingtime won‟t be recalculated when pressing Enter/Cancel button;(2) If cleaning time is reached, in unit on or off state, will blink every 0.5s for reminder. PressFunction button to switch to icon and press ▲ and ▼ button to adjust the level. Then pressEnter/Cancel button, so the accumulated operating time won‟t be cleared (If the adjusted level ishigher than the present accumulated operating time, the icon won‟t blink any more; if the adjustedlevel is lower than the present accumulated operating time, the icon will go on blinking).(3) The only way to cancel filter clean reminder function is to press Function button to switch to filterclean reminder function. The icon will blink and press ▲ or ▼ button to adjust timer zone todisplay “00”. In this case, the accumulated operating time will be cleared.4.2 Low Temperature Drying FunctionUnder dry mode and when set temperature is 16℃(61℉), continuously press ▼ button for twice andthen the set temperature will be 12℃ (54℉). In this case, the unit will enter low temperature dryingfunction.When low temperature drying function is turned on, press ▲ button or Mode button to exit lowtemperature drying function.4.3 Lock FunctionWhen unit is turned on normally or turned off, pressing ▲ and ▼ buttons at the same time for 5s willturn on Lock function. LCD will display . Pressing ▲ and ▼ buttons at the same time for 5s to turn offthis function.When Lock function is turned on, any other buttons won‟t respond when pressing. The function can bememorized after power failure and then power recovery.