Relion 615 ® seriesMotor protection and controlREM615 ANSIProduct guide

Description

Standard conﬁ gurations

Protection functions

Application

Supported ABB solutions

Control

Self-diagnostics

Access control

Communication

Technical data

Mounting methods

Selection and ordering data

Accessories and ordering data

Tools

Terminal diagrams

Certiﬁ cates

Functions, codes and symbols

Document revision history

Notes

ABB REM615 ANSI Product Manual

Protections functions

Recorded data

Current circuit supervision

Local HMI

IED case and IED plug-in unit

References

REM615 ANSI

Section 1 Introduction

Product documentation

Section 2 Modbus data mappings

Indications

Premapped indications

CTRL.CBCSWI1 Circuit breaker (1) mom+mcd position

CTRL.DCSXSWI2 Disconnector position indication (2 29DS-1

CTRL.DCXSWI2 Disconnector control (2) – 29DS-2

CTRL.ESXSWI1 Grounding switch control (1) – 29GS-1

LD0.ARCSARC2 Arc protection (2) – AFD-2

LD0.CCSPVC1 Current circuit supervision (1) – CCM-1

LD0.DOPPDPR1 Reverse power/directional overpower protection (1) – 32O-1

LD0.DUPPDPR1 Underpower protection (1) – 32U-1

LD0.EFHPTOC2 Non-directional ground-fault protection high stage (2) – 50G-2

LD0.FRPFRQ2 Frequency protection (2) – 81-2

LD0.HIBPDIF1 High-impedance differential protection for phase B (1) – 87B-1

LD0.LEDGGIO1 Indication LED states Color1/Color2 – LED

LD0.LEDGGIO1 Indication LED states OFF/ColorX – LED

LD0.LEDPTRC1 Global conditioning (1)

LD0.LOFLPTUC1 Loss of load supervision (1) – 37M-1

LD0.MAPGAPC2 Multipurpose protection (2) – MAP-2

LD0.MAPGAPC5 Multipurpose protection (5) – MAP-5

LD0.MNSPTOC1 Negative-sequence overcurrent protection for machines (1) – 46M-1

LD0.MVGAPC1 Move (8 pcs) (1) – MV-1

LD0.NSPTOV1 Negative-sequence overvoltage protection

LD0.OEPVPH1 Overexcitation protection (1) – 24-1

LD0.PHHPTOC2 Three-phase non-directional overcurrent protection, high stage (2) – 50P-2

LD0.PHLPTOC1 Three-phase non-directional overcurrent protection, low stage (1) – 51P-1

LD0.PHPTOV2 Three-phase overvoltage protection (2) – 59-2

LD0.PREVPTOC1 Phase reversal protection (1) – 46R-1

LD0.RESCMMXU1 Residual current measurement (1) – IG-1

LD0.ROVPTOV2 Residual overvoltage protection (2) – 59N-1

CM-1

LD0.STTPMSU1 Motor start-up supervision (1) – 66/51LRS-1

LD0.TRPPTRC1 Master trip (1) – 86/94-1

LD0.XAGGIO130 Physical I/O states (AIM card XA130)

LD0.XGGIO100 Physical I/O states (PSM card X100)

LD0.XGGIO110 Physical I/O states (BIO card X110)

LD0.XGGIO120 Physical I/O states (AIM card X120)

LD0.XGGIO130 Physical I/O states (BIO card X130)

LD0.XRGGIO130 Alarm/warning

LD0.DIAGLCCH1 Ethernet supervision (1)

LD0.LDPRLRC1 Load profile record (1) – LoadProf

LD0.MAPGAPC9 Multipurpose protection (9) – MAP-9

LD0.MAPGAPC12 Multipurpose protection (12) – MAP-12

LD0.MAPGAPC15 Multipurpose protection (15) – MAP-15

LD0.MAPGAPC18 Multipurpose protection (18) – MAP-18

LD0.RESTVTR1 VG VT supervision (1)

LD0.TRPPTRC3 Master trip (3) – 86/94-3

LD0.TRPPTRC5 Master trip (5) – 86/94-5

LD0.UDFCNT1 Multipurpose generic up-down counter (1 CTR-1

LD0.UDFCNT4 Multipurpose generic up-down counter (4 CTR-4

Control structure 1

Control structure 4

Control structure 7

Fault record structure header

Protection relay's real-time clock (in local time mode) - read and write (synchronize)

Indication bits mirrored in registers

SSR2 System status register (2) protection relay's mode and state

SSR4 System status register (4) data available 2 (client dependent, user-definable)

SSR6 System status register (6) control command status client-dependent)

Time and reason for latest protection relay reset

User-definable registers [Alt.1], visible on 3x and 4x

LD0.CMMXU1 Phase current demand values (1) – IA, IB, IC

LD0.CMMXU1 Three-phase current measurement (1) – IA IB, IC

LD0.MDSOPT1 Runtime counter for machines and devices 1) – OPTM-1

LD0.PEMMXU1 Power measurement demand values (1) – P E-1

LD0.RESCMMXU1 Residual current demand value (1) – IG-1

LD0.RESVMMXU1 Residual voltage demand value (1) – VG-1

LD0.VMMXU1 Three-phase voltage measurement (1) – VA VB, VC

LD0.VMMXU1 Voltage demand values (1) – VA, VB, VC

Unmapped registers

LD0.SCA4GAPC1 Analog value scaling (1) – SCA4-1

LD0.SCA4GAPC4 Analog value scaling (4) – SCA4-4

LD0.SPEMMXU1 Single-phase power and energy measurement demand values (1) – SP, SE-1

ABB REM615 ANSI Product Manual

Product

Learn More

Legal


Contents Table Of Contents Description Standard conﬁ gurations Protection functions Application Supported ABB solutions Control Self-diagnostics Access control Communication Technical data Mounting methods Selection and ordering data Accessories and ordering data Tools Terminal diagrams Certiﬁ cates Functions, codes and symbols Document revision history Notes	Relion 615 ® seriesMotor protection and controlREM615 ANSIProduct guide Next / 46