2easy DMR12/S8 Quick Installation Manual

Contents

dip switches settings

2easy DMR12/S8 Quick Installation Manual Manual pdf 1 page image

2. Parts and functions6. Place Name Plate1. IntroductionsDoor Station is a unit installed on the entrance of a building, which used to call auser in a apartment, and control the electronic lock opening.This is a guide for quick installation. for more detail instructions, please refer to theDT system technical guide.To call the user, press a button with a associated nameplate of the user; then theuser will press the Unlock button on the monitor to open the door for the visitor ifshe/he is accepted.A ID card can be use to open the door.(Only for DMR12/ID series Door Station).For detail ID card operation, please refer to DT system technical guide.A exit button can be connect to the Door Station directly.The Camera angle can be adjusted to coordinate the install position of the DoorStation3. Terminals1.Remove the bottom cover 2.Remove the anti-theft screw 3.Extract name plate folder,replace name plate-1- -2- -3-1 2 3 4 5 6ONT/R -T/R+RS-485SETL1+12VLK - (GND)CN-LKJP-LKBUSLK+(COM)N.O.EB -EB+321L2DIP• +12V: 12VDC power output.• LK-(GND): power ground.• LK+(COM): electronical load activation ralay contact common.• NO.: electronical load activation ralay normally open contact(refer to DT technicalguide for Lock connection detail informations).• EB+: Exit button.• EB-: Exit buton.• JP-LK: For electronic lock safety type setting(refer to Door Station LockConnections).• T/R-: USB-RS485 communication terminal negative.• T/R+: USB-RS485 communication terninal positive.• SET: DIP switches for system configurations.• Bus(L1,L2): non-polarised bus line.4. ConnectionsThis example is one door station wiring, note that the lock used here is a 12Vdc 300mApower-to-unlock type. (please refer to DT technical guide for Lock connection detailinformations)L1+12VLK - (GND)CN-LKJP-LKBUSLK+(COM)N.O.EB -EB+321L2Connect to DPS or DBC4SExit ButtonElectronic Lock+-5. DIP Switches settingsTotal 6 bits in the DIP switches can be configured. The switches can be modifiedeither before or after installation.• Bit-1 and Bit 2 is for door station ID settings, when mutil door stations areinstalled in the system, these two bit must be set correctly, the first doorstation set to 00, the second one set to 01, the third one set to 10, the fourthone set to 11. If only one door station is installed, set to 00.• Bit-3: Single line button door station or double line button door stationselection. If the door station is a double line button, for examlpe, the DMR12/D16, set this bit to 0, set to 1 for single line button door stations.• Bit-4: Button code selection; if use the default codes for each button of thedoor station, set to 0, if use the programmed codes, set to 1.(the code foreach button can be program by the 2Easy+TOOL software, see the programsection in this manual)• Bit-5: Unlocking time quick selection, by default it is set to 0, for 1 secondunlocking time; set to 1 for 5 seconds(by default).• Bit-6: Set to 1,it is for door station ID settings,for examlpe,the DMR12/ID/S4 and DMR12/ID/D8 must be set to 1;set to 0,it is not for door station IDsettings,for example,the DMR12/S8 and DMR12/D16 must be set to 0.ON(1) OFF(0)1 2 3 4 5 6ON DIPON ONSpeakerCamera LensMicrophoneName plateCall buttonCamera AngleadjustmentWith rainy cover

/ 2

Related manuals for 2easy DMR12/D16