OneStart

Menu

ABB +N5600 manuals

+N5600 first page preview

+N5600

Brand: ABB | Category: Controller
Table of contents
  1. List of related manuals
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Table Of Contents
  7. Table Of Contents
  8. Table Of Contents
  9. What this chapter contains
  10. Licensing
  11. Contents of the manual
  13. Local control vs. external control
  14. External control
  15. Operating modes of the drive
  16. Speed control mode
  17. Contents of this chapter
  18. Drive start-up
  19. ESP application minimum configuration
  21. Backspin supervision
  22. Backspin speed observer constraints
  23. Starting the motor
  24. Kick-start
  25. Current pulse-start
  26. ESP production mode
  27. Automatic process control mode
  28. Underload and overload protection
  29. Underload ride through recovery sequence
  30. Overload recovery sequence
  31. Motor voltage control
  32. Pump impeller cleaning
  33. Pump curves
  35. Drive configuration and programming
  36. Adaptive programming
  37. Control interfaces
  38. Programmable relay outputs
  39. Fieldbus control
  40. Master/follower functionality
  41. External controller interface
  42. Control of a supply unit (LSU)
  43. Motor control
  44. Constant speeds/frequencies
  45. Speed controller autotune
  46. Oscillation damping
  47. Resonance frequency elimination
  48. Encoder support
  49. Jogging
  50. Scalar motor control
  51. Autophasing
  52. Flux braking
  53. DC magnetization
  54. Hexagonal motor flux pattern
  55. Application control
  56. Motor potentiometer
  57. Mechanical brake control
  58. DC voltage control
  59. Voltage control and trip limits
  60. Brake chopper
  61. Safety and protections
  62. Motor thermal protection
  63. Thermal protection of motor cable
  64. Automatic fault resets
  65. Other programmable protection functions
  66. Diagnostics
  67. Energy saving calculators
  68. Miscellaneous
  69. User lock
  70. Reduced run function
  71. du/dt filter support
  73. Factory macro
  74. Default control connections for the Factory macro
  75. Hand/Auto macro
  76. Default control connections for the Hand/Auto macro
  77. PID control macro
  78. Default parameter settings for the PID control macro
  79. Default control connections for the PID control macro
  80. Sensor connection examples for the PID control macro
  81. Torque control macro
  82. Default control connections for the Torque control macro
  83. Sequential control macro
  84. Selection of constant speeds
  85. Default control connections for the Sequential control macro
  86. Fieldbus control macro
  88. Terms and abbreviations
  89. Summary of parameter groups
  90. Parameter listing
  91. Input references
  92. Warnings and faults
  94. Control and status words
  95. System info
  96. ESP signals
  97. Standard DI, RO
  98. Standard DIO, FI, FO
  99. Standard AI
  100. Standard AO
  101. I/O extension module 1
  102. I/O extension module 2
  103. I/O extension module 3
  104. Operation mode
  105. Start/stop/direction
  106. Start/stop mode
  107. Speed reference selection
  108. Speed reference ramp
  109. Speed reference conditioning
  110. Speed control
  111. Torque reference chain
  112. Frequency reference chain
  113. Limits
  114. Fault functions
  115. Supervision
  116. Generic timer & counter
  118. Load analyzer
  119. User load curve
  120. Process PID set 1
  121. Process PID set 2
  124. Energy efficiency
  125. Monitoring/scaling settings
  126. Data storage
  127. Panel port communication
  128. Fieldbus adapter (FBA)
  129. FBA A settings
  130. FBA B settings
  131. Embedded fieldbus
  132. DDCS communication
  133. D2D and DDCS transmit data
  134. D2D and DDCS receive data
  135. ESP control
  136. ESP reference setup
  137. ESP automatic control
  138. Load protection
  139. Voltage control
  140. Pump cleaning
  141. Q-H pump curves
  142. Feedback selection
  143. Encoder module settings
  144. Encoder 1 configuration
  145. Encoder 2 configuration
  146. LSU control
  147. HW configuration
  148. System
  150. User motor parameters
  151. Motor data
  152. Safety
  154. Fieldbus addresses
  155. Parameter groups 1...9
  156. Parameter groups 10...99
  158. Pure events
  159. Other data loggers
  160. QR Code generation for mobile service application
  161. Warning messages
  162. Fault messages
  164. Connecting the fieldbus to the drive
  165. Setting up the embedded fieldbus interface
  166. Setting the drive control parameters
  167. Basics of the embedded fieldbus interface
  168. Control word and Status word
  169. Register addressing
  170. About the control profiles
  171. The ABB Drives profile
  172. Status Word
  173. State transition diagram
  174. References
  175. Actual values
  176. Modbus holding register addresses
  177. The Transparent profile
  178. Modbus function codes
  179. Exception codes
  180. Coils (0xxxx reference set)
  181. Discrete inputs (1xxxx reference set)
  182. Error code registers (holding registers 400090...400100)
  184. Basics of the fieldbus control interface
  187. Contents of the fieldbus Control word (ABB Drives profile)
  188. Contents of the fieldbus Status word (ABB Drives profile)
  189. The state diagram (ABB Drives profile)
  190. Setting up the drive for fieldbus control
  191. Parameter setting example: FPBA (PROFIBUS DP)
  193. Speed reference source selection I
  194. Speed reference source selection II
  195. Speed reference ramping and shaping
  196. Motor feedback configuration
  197. Load feedback and position counter configuration
  198. Speed error calculation
  199. Speed controller
  200. Torque reference source selection and modification
  201. Operating mode selection
  202. Reference selection for torque controller
  203. Torque limitation
  204. Torque controller
  205. Frequency reference selection
  206. Frequency reference modification
  207. Process PID setpoint and feedback source selection
  208. Process PID controller
  209. Master/Follower communication I (Master)
  210. Master/Follower communication II (Follower)
  211. Product and service inquiries
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved