Menu
Samsung DVM S AM200FXVAGR manuals
DVM S AM200FXVAGR
Table of contents
- installation manual
- Table Of Contents
- safety precautions
- Preparing the installation
- selecting installation location
- hydro unit
- Base construction and installation of the DVM Hydro unit / Hydro unit HT
- Refrigerant pipe installation
- Performing leak test and insulation
- Installing the drain pipe
- Water pipe installation
- Connecting power and communication cable
- Connecting external contact
- Setting an indoor unit address and installation option
- Product maintenance
- Failure diagnosis
- Error code
- Using the PCB Switch
- Completing the installation
- Appendix
DVM S AM200FXVAGR
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Precautions
- Precautions for Handling Refrigerant for Air Conditioner
- Product Specifications
- Changes in comparison to basic mode
- Structure of product(Heat Pump)
- Structure of product(Heat Recovery)
- Structure of product(Power supply for 460V, 60Hz, 3Φ)
- Structure of product (DVM S WATER)
- Structure of product (Heat Pump AM KX Series)
- Accessory and Option Specifications
- Disassembly and Reassembly
- AM140FXVAGH, AM140JXV GH
- AM160/180/200/220/240/260 XV , AM140JXVA H
- AM080/100/120FXWA
- AM200FXWA
- Caution at compressor exchange
- Troubleshooting
- Service Operation
- DVM S Models EEPROM Code Table
- Number Display Method
- Appropriate Measures for Different Symptom
- Main PCB has no power phenomenon
- Communication Error between Indoor and Outdoor Units during Tracking
- Communication Error between Indoor and Outdoor Units after Tracking
- between outdoor units
- Internal Communication error of the Outdoor Unit C-Box
- Internal PCB Communication error of the Outdoor Unit C-Box
- of 2 branch Parts
- MCU branch part setup error-Repeated setup for the same address over 3 times
- MCU branch part setup error-non-installed address setup
- Setup Error for MCU Branch part-Setup Error for MCU Quantity Used
- MCU branch part setup error-Overlapping Indoor unit Address setup
- to an Indoor unit
- not being used
- actually set up in MCU
- MCU/MCU subcooler entrance/exit sensor error (Open/Short)
- Outdoor Temperature Sensor Error
- Cond Out Temperature Sensor Error (Open/Short)
- outdoor cond out sensor breakaway error
- Compressor Discharge or TOP 1/2 Temperature sensor error
- High Pressure sensor error (Open/Short)
- Low Pressure sensor error (Open/Short)
- Suction Temperature sensor error (Open/Short)
- Liquid Pipe Temperature sensor error (Open/Short)
- EVI In Temperature sensor error (Open/Short)
- EVI Out Temperature sensor error (Open/Short)
- Suction-2 Temperature Sensor Error (Open/Short)
- Measures of other outdoor unit error
- temperature sensor/Top temperature sensor
- phase Input Wiring error
- EVI EEV Open error
- Refrigerant leakage error
- Prevention of heating/cooling operation due to outdoor temperature
- Prevention of heating refrigerant charge due to outdoor temperature
- CH wire breaking error
- Fan starting error
- Fan lock error
- Momentary Blackout error
- Outdoor Fan Motor overheating
- Fan IPM Overheat error
- Compressor starting error
- COMP Overcurrent error
- Overvoltage/Low voltage error
- DC Link voltage sensor error
- Fan Motor Overcurrent error
- PCB Diagram and Parts List
- ASS'Y PCB MAIN-HUB
- ASS'Y PCB INVERTER
- ASS'Y PCB FAN
- ASS'Y PCB EMI
- SUB-COMM
- Wiring Diagram
- AM080/100/120/200FXWA
- AM080JXVAFH
- AM100/120JXVAFH
- AM140/160/180/200JXVAFH
- AM080/100/120/140/160/180/200/220JXVAJH
- Cycle Diagram
- AM080/100/120 XV GR
- AM160/180/200/220 XV GR
- AM240/260HXVAGH/EU
- Cooling operation (H/R)
- Main cooling operation (H/R)
- Heating operation (H/R)
- Main heating operation (H/R)
- Cooling operation (H/P)
- Heating operation (H/P)
- Main cooling operation(H/R)
- Heating operation(H/R)
- Main heating operation(H/R)
- Cycle Component Function Explanation
- Key Options
- How to set the key function of the outdoor unit
- How to check the view mode using a tact switch
- Test Operation
- Auto Trial Operation functions
- How to troubleshoot of the "Undetermined"
- Amount of refrigerant automatically checking
- Model Naming
DVM S AM200FXVAGR
Table of contents
- air conditioner
- Table Of Contents
- Safety precautions
- Preparing for installation
- outdoor unit combination
- moving the outdoor unit
- Selecting installation location
- Space requirement for installation
- Accessories
- Base construction and installation of the outdoor unit
- outdoor unit installation
- Installing the wind/snow prevention duct
- Refrigerant pipe installation
- additional refrigerant
- cutting or flaring the pipes
- installing the branch joints
- Electrical wiring work
- power wiring diagram
- selecting solderless ring terminal
- connecting the power terminal
- grounding work
- Air tightness test and vacuum drying
- Pipe insulation
- insulating the branch joint
- Charging refrigerant (for the turkish market only)
- Basic segment display
- Setting the MCU and Pipe Addresses (for HR Only)
- Things to check after completing the installation
- Inspection and test operation
- Automatic refrigerant amount detection function
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved