Panasonic CPC-EX manuals

CPC-EX

Brand: Panasonic | Category: Telephone

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. Table Of Contents
8. Table Of Contents
9. about this manual
10. Chapter 1 Requirements
11. Table 1-2. FCC information
12. DID Requirements
13. T1 Requirements
14. Cleaning
15. Chapter 2 System Overview
16. Cabinet Description
17. Configurations
18. Printed Circuit Cards
19. Table 2-3. Printed circuit package slot usage
20. Processor Description
21. Chapter 3 Cabinet Installation
22. Wall-Mounting the Cabinet
23. Figure 3-2. Cabinet mounting bracket
24. Grounding
25. Card Installation
26. Figure 3-6. CPC Strap S1
27. Installation
28. Battery Backup
29. Installation for the DBS 40
30. Installation for the DBS 72 and 96
31. Figure 3-10. Battery pack connection, DBS 72 and 96
32. Key Phone Wall Mounting
33. Figure 3-12. Wall-mount adaptor replacement
34. DSLT Wall Mounting
35. Figure 3-15. Desk stand attachment for DSLT wall mounting
36. System Initialization
37. Test Phone
38. Figure 3-18. Test telephone connection
39. Chapter 4 Trunks and Lines
40. Trunks
41. Trunk Connector Pinouts
42. Table 4-2. Pinouts and trunk numbers for the main trunk connector
43. Table 4-3. Pinouts and trunk numbers for trunk expansion connector CN1
44. Loop-Start Trunks
45. Figure 4-3. Attaching Caller ID Card to the L-TRK Card
46. Ground Start and DID Trunks
47. Figure 4-4. -48Vpower supply installation
48. T1 Interface
49. Table 4-7. T1 Hardware requirements for double-cabinet systems
50. Table 4-8. T1 slot usage for two-cabinet systems
51. Table 4-9. T1 and analog trunk assignments, DBS 40
52. Table 4-11. T1 and analog trunk assignments, DBS 96
53. Table 4-13. T1 and analog trunk assignments, DBS 40 + 40 (16-channel fractional T1 in the slave)
54. Table 4-15. T1 and analog trunk assignments, DBS 96 + DBS 40 (24-channel T1 in the master 16-channel T1 in the slave)
55. Table 4-16. T1 and analog trunk assignments, DBS 96 + DBS 72 (24-channel T1 in the master 24-channel T1 in the slave)
56. Table 4-17. T1 and analog trunk assignments, DBS 96 + DBS 96 (24-channel T1 in the master 24-channel T1 in the slave)
57. Figure 4-5. Connector 4 (CN4) strapping, Sync Unit
58. Figure 4-6. T1 Sync Unit installation
59. Figure 4-7. T1 MDF card installation
60. Figure 4-8. Sync Unit and T1 connection, single-cabinet installation
61. Figure 4-9. RJ48 pinouts, CN1 connector
62. Figure 4-10. T1 cabinet connections, single-cabinet installation
63. Figure 4-11. Sync cable connections, double-cabinet with a T1 in the slave
64. Figure 4-12. Clock sync cable and sync cable connections, double-cabinet installation
65. Lines
66. Extension Connector Pinouts
67. Analog Extensions
68. Figure 4-14. SLT ringer box installation
69. Figure 4-15. EMI filter installation (DBS 40 only)
70. Digital Extensions
71. Figure 4-16. DSS/72 connection using one cable with two pairs
72. Figure 4-17. EM/24 connection using one cable with two pairs
73. Trunk and Line Expansion
74. Figure 4-18. Trunk or extension expansion
75. Chapter 5 Peripheral Equipment
76. Local Terminal or SMDR Device
77. Figure 5-1. RS-232C connection
78. Figure 5-2. SMDR Format for CPC-AII and CPC-B Version 3.1 or higher
79. Remote Administration Interface (RAI)
80. Figure 5-3. RAI connection
81. Background Music/Music-On-Hold
82. Figure 5-4. Installation of music-on-hold and background music
83. Off-Premises Adaptor (OPX)
84. Figure 5-5. Cable punch-out plate, OPX Adaptor
85. Figure 5-6. OPX installation
86. Paging
87. Figure 5-7. External zone paging installation
88. External General Page/UNA Installation
89. External Ringer (UNA Device)
90. Figure 5-9. External ringer (UNA device) installation
91. Power Failure Unit
92. Figure 5-10. Cable punch-out plate, Power Failure Unit
93. Figure 5-11. Power Failure Unit (PFU) installation
94. Voice Announce Unit (VAU)
95. Figure 5-12. Cable punch-out plate, Voice Announce Unit
96. Figure 5-13. Extension cord connection to the VAU
97. Recording and Playing Messages
98. Door Box Adaptor (Trunk Port)
100. Figure 5-15. Cable punch-out plate, Door Box Adaptor
101. Figure 5-16. Installation of the door box, door opener, and door sensor
102. Door Box Adaptor (Extension Port)
103. Figure 5-18. Installation of the door box, door opener
104. Figure 5-19. Connections to the Door Box Adaptor
105. Single Line Telephone Adaptor
106. Figure 5-21. SLTA installation
107. Chapter 6 Double-Cabinet Systems
108. Guidelines
109. Figure 6-1. Slot usage for two-cabinet systems, DBS 40 + DBS 40
110. Figure 6-2. Slot usage for two-cabinet systems, DBS 72 + DBS 40
111. Figure 6-3. Slot usage for two-cabinet systems, DBS 72 + DBS 72
112. Figure 6-4. Slot usage for two-cabinet systems, DBS 96 + DBS 40
113. Figure 6-5. Slot usage for two-cabinet systems, DBS 96 + DBS 72
114. Figure 6-6. Slot usage for two-cabinet systems, DBS 96 to DBS 96
115. Figure 6-7. Strap 3, MFR card
116. Figure 6-8. Double-cabinet installation
117. Chapter 7 Specifications
118. Electrical Characteristics
119. Environmental Requirements
120. Resource Maximums
121. Table 7-9. Hardware maximums for single-cabinet systems
122. Table 7-10. Hardware maximums for double-cabinet systems
123. Cabling Specifications
124. Communication Parameters
125. Signaling Characteristics
126. Tone Characteristics
127. Table 7-18. DTMF frequencies
128. Appendix A: CPC-EX 1.0 Updates
129. Directory Mode
130. FF-Key Programming
131. SMDR Modifications
132. Series Enhanced Phone Features
133. Analog Adapter
134. MSG (Message) Key
135. DSS/72 Console - Key Arrangement
136. Additional Serial Port on CPC Card
137. Appendix B: CPC-AII/B 8.0 Updates
138. Contents
139. Series Phone Support
140. Enhanced Phone Features
144. page b
145. EM/24 - Key Arrangement
146. TAPI Support
147. Index