ABB ACS880-04XT manuals

ACS880-04XT

Brand: ABB | Category: Industrial Electrical

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Contents of this chapter
5. Related manuals
7. Selecting the main contactor (breaker)
8. Selecting the supply transformer
9. Additional notes
10. A drive with a 12-pulse diode supply unit
11. Examining the compatibility of the motor and drive
12. Availability of du/dt filter and common mode filter by drive type
13. Additional requirements for non-ABB high-output and IP23 motors
14. Additional data for calculating the rise time and the peak line-to-line voltage
15. Selecting the power cables
16. Alternative power cable types
17. Not allowed power cable types
18. Additional US requirements
19. Selecting the control cables
20. Routing the cables
21. Separate control cable ducts
22. Implementing thermal overload and short circuit protections
23. Multidrive modules
24. Implementing a motor temperature sensor connection
25. Implementing a ground fault protecting function
26. Implementing the Emergency stop function
27. Implementing the Prevention of unexpected start-up function
29. Implementing the Power-loss ride-through
30. Implementing a bypass connection
32. Applicable standards
33. Markings
34. EMC compliance (IEC/EN 61800-3:2004 + A2012)
35. Category C3
36. EU Declaration of Conformity (Machinery Directive)
37. UL and CSA checklist
38. Disclaimers

ACS880-04XT

Brand: ABB | Category: DC Drives

ACS880-04XT

Brand: ABB | Category: Industrial Equipment

ACS880-04XT

Brand: ABB | Category: Servo Drives

ACS880-04XT

Brand: ABB | Category: Controller

Table of contents

1. List of related manuals
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. Table Of Contents
8. Table Of Contents
9. What this chapter contains
10. Licensing
11. Contents of the manual
13. Local control vs. external control
14. External control
15. Operating modes of the drive
16. Speed control mode
17. Contents of this chapter
18. Drive start-up
19. ESP application minimum configuration
21. Backspin supervision
22. Backspin speed observer constraints
23. Starting the motor
24. Kick-start
25. Current pulse-start
26. ESP production mode
27. Automatic process control mode
28. Underload and overload protection
29. Underload ride through recovery sequence
30. Overload recovery sequence
31. Motor voltage control
32. Pump impeller cleaning
33. Pump curves
35. Drive configuration and programming
36. Adaptive programming
37. Control interfaces
38. Programmable relay outputs
39. Fieldbus control
40. Master/follower functionality
41. External controller interface
42. Control of a supply unit (LSU)
43. Motor control
44. Constant speeds/frequencies
45. Speed controller autotune
46. Oscillation damping
47. Resonance frequency elimination
48. Encoder support
49. Jogging
50. Scalar motor control
51. Autophasing
52. Flux braking
53. DC magnetization
54. Hexagonal motor flux pattern
55. Application control
56. Motor potentiometer
57. Mechanical brake control
58. DC voltage control
59. Voltage control and trip limits
60. Brake chopper
61. Safety and protections
62. Motor thermal protection
63. Thermal protection of motor cable
64. Automatic fault resets
65. Other programmable protection functions
66. Diagnostics
67. Energy saving calculators
68. Miscellaneous
69. User lock
70. Reduced run function
71. du/dt filter support
73. Factory macro
74. Default control connections for the Factory macro
75. Hand/Auto macro
76. Default control connections for the Hand/Auto macro
77. PID control macro
78. Default parameter settings for the PID control macro
79. Default control connections for the PID control macro
80. Sensor connection examples for the PID control macro
81. Torque control macro
82. Default control connections for the Torque control macro
83. Sequential control macro
84. Selection of constant speeds
85. Default control connections for the Sequential control macro
86. Fieldbus control macro
88. Terms and abbreviations
89. Summary of parameter groups
90. Parameter listing
91. Input references
92. Warnings and faults
94. Control and status words
95. System info
96. ESP signals
97. Standard DI, RO
98. Standard DIO, FI, FO
99. Standard AI
100. Standard AO
101. I/O extension module 1
102. I/O extension module 2
103. I/O extension module 3
104. Operation mode
105. Start/stop/direction
106. Start/stop mode
107. Speed reference selection
108. Speed reference ramp
109. Speed reference conditioning
110. Speed control
111. Torque reference chain
112. Frequency reference chain
113. Limits
114. Fault functions
115. Supervision
116. Generic timer & counter
118. Load analyzer
119. User load curve
120. Process PID set 1
121. Process PID set 2
124. Energy efficiency
125. Monitoring/scaling settings
126. Data storage
127. Panel port communication
128. Fieldbus adapter (FBA)
129. FBA A settings
130. FBA B settings
131. Embedded fieldbus
132. DDCS communication
133. D2D and DDCS transmit data
134. D2D and DDCS receive data
135. ESP control
136. ESP reference setup
137. ESP automatic control
138. Load protection
139. Voltage control
140. Pump cleaning
141. Q-H pump curves
142. Feedback selection
143. Encoder module settings
144. Encoder 1 configuration
145. Encoder 2 configuration
146. LSU control
147. HW configuration
148. System
150. User motor parameters
151. Motor data
152. Safety
154. Fieldbus addresses
155. Parameter groups 1...9
156. Parameter groups 10...99
158. Pure events
159. Other data loggers
160. QR Code generation for mobile service application
161. Warning messages
162. Fault messages
164. Connecting the fieldbus to the drive
165. Setting up the embedded fieldbus interface
166. Setting the drive control parameters
167. Basics of the embedded fieldbus interface
168. Control word and Status word
169. Register addressing
170. About the control profiles
171. The ABB Drives profile
172. Status Word
173. State transition diagram
174. References
175. Actual values
176. Modbus holding register addresses
177. The Transparent profile
178. Modbus function codes
179. Exception codes
180. Coils (0xxxx reference set)
181. Discrete inputs (1xxxx reference set)
182. Error code registers (holding registers 400090...400100)
184. Basics of the fieldbus control interface
187. Contents of the fieldbus Control word (ABB Drives profile)
188. Contents of the fieldbus Status word (ABB Drives profile)
189. The state diagram (ABB Drives profile)
190. Setting up the drive for fieldbus control
191. Parameter setting example: FPBA (PROFIBUS DP)
193. Speed reference source selection I
194. Speed reference source selection II
195. Speed reference ramping and shaping
196. Motor feedback configuration
197. Load feedback and position counter configuration
198. Speed error calculation
199. Speed controller
200. Torque reference source selection and modification
201. Operating mode selection
202. Reference selection for torque controller
203. Torque limitation
204. Torque controller
205. Frequency reference selection
206. Frequency reference modification
207. Process PID setpoint and feedback source selection
208. Process PID controller
209. Master/Follower communication I (Master)
210. Master/Follower communication II (Follower)
211. Product and service inquiries