ABB ACS800-37LC-5960-7 manuals

ACS800-37LC-5960-7

Brand: ABB | Category: DC Drives

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. Table Of Contents
8. What this chapter contains
9. Safety in installation and maintenance
10. Grounding
11. Permanent magnet motor drives
12. General safety
13. Use of the hand-operated winch
14. Safe start-up and operation
16. Related documents
17. Terms and abbreviations
19. Single-line circuit diagram of the drive
20. Example circuit diagram (frame 2×R8i+2×R8i)
21. Block diagram of the main circuit with options
22. General information on drive cabinet layout
23. Cabinet layout (frames R7i+R7i and R8i+R8i)
24. Swing-out frame layout
25. Auxiliary control cubicle layout
26. Main switch disconnecter cubicle layout (frames 2×R8i+2×R8i and up)
27. Layout of LCL filter and supply module cubicles (frame 2×R8i and up)
29. Layout of inverter module cubicle (frame 2×R8i)
30. Layout of inverter module cubicle (frame 3×R8i)
31. Layout of inverter module cubicles (frames 4×R8i to 9×R8i)
32. Overview of supply and inverter modules (R7i and R8i)
33. Overview of power and control connections
34. Control of the supply unit
35. Emergency stop push button
36. Connections and use of the I/O in the supply unit
37. Connections to standard I/O terminals
38. Control of the inverter unit and motor
39. Type designation labels
40. Type designation key
42. Checking the delivery
43. Moving the unit by fork-lift or pallet truck
44. Placing the unit
45. Overview of the installation procedure
46. Fastening the cabinet to the floor and wall (non-marine units)
47. Alternative 2 – Using the holes inside the cabinet
48. Fastening the unit to the floor and wall (marine units, option +C121)
49. Joining the shipping splits
50. Connecting the liquid pipes
51. Connecting the DC busbars
52. Miscellaneous
53. Electric welding
55. Protecting the motor insulation and bearings
56. Requirements for motor insulation and bearings and drive filters
57. Explosion-safe (EX) motors
58. High-output motors and IP 23 motors
59. Sine filters
60. Typical power cable sizes
61. Alternative power cable types
62. Additional US requirements
63. Relay cable
64. Separate control cable ducts
65. Protecting the motor and motor cable in short-circuit situations
66. Insulation requirements for the motor temperature sensor circuit
67. Implementing the Prevention of unexpected start function
68. Implementing the Safe torque off function
69. Terminals for connecting external control voltage (option +G307)
70. Implementing a safety switch between the drive and motor
71. Implementing a bypass connection
72. Switching the motor power supply from direct-on-line to drive
73. Considering the PELV on installation sites above 2000 metres (6562 feet)
75. Braking resistor assembly
76. Connecting the input power cable
77. Connecting the motor cable – units with no common motor terminals cubicle option +H359
78. Connection diagram – parallel inverter modules feed one motor
79. Connection procedure
80. Connection diagram
81. Connecting external power supply for the auxiliary circuits
82. Frames 2×R8i and up
83. tional auxiliary control voltage transformer
84. Connecting the control cables for the inverter unit
86. Connecting a PC
87. Cabling of I/O and fieldbus modules
90. Connecting voltage to the input terminals and auxiliary circuit
91. On-load checks
92. Switching the control panel between the supply and inverter units
93. ACS800-17LC-specific parameters in the IGBT Supply Control Program
94. Default values of parameters with the ACS800-17LC
95. ACS800-17LC-specific parameters in the application program
96. LEDs
98. Replacing the additional fan in the incoming cubicle (frames R7i+R7i and R8i+R8i)
99. Replacing the auxiliary control cubicle fan (frames 2×R8i+2×R8i and up)
100. Replacing the fan in the incoming cubicle (frames 2×R8i+2×R8i and up)
101. Replacing the cooling fans in supply module cubicle
102. Replacing the inverter module fans (2×R8i and up)
103. Reduced run capability
104. Replacing supply and inverter modules
105. Installing the winch
106. Installing the installation stand
107. Capacitors
108. Replacing the PPCS branching unit (APBU-xx) memory backup battery
109. General
110. Connection to a cooling unit
111. Filling up and bleeding the internal cooling circuit
112. Draining the internal cooling circuit
113. Specifications
114. Water quality
115. Materials
117. Definitions
118. Altitude derating
119. phase brake choppers (option +D150) and resistors (option +D151)
120. Fuses
121. Main circuit DC fuses
122. Dimensions, weights and free space requirements
123. Losses, cooling data and noise
124. Internal cooling circuit data
125. Terminal and lead-through data for the input power cable
126. Terminal and lead-through data for the motor cable
127. Units with the Common Motor Terminal (CMT) cubicle (option +H359)
128. Electrical power network specification
129. Control unit (RDCU/RMIO) connection data
130. Relay outputs
131. Isolation and grounding diagram
132. Ambient conditions
133. Auxiliary circuit current consumption
134. Applicable standards
135. CE marking
136. Category C2
137. Category C4
138. UL marking
139. Cyber security disclaimer
141. Frame sizes R7i+R7i and R8i+R8i (bottom entry/exit)
142. Frame sizes R7i+R7i and R8i+R8i (marine units, +C121)
143. Product and service inquiries