Panasonic Viera TX-26LXD71F Operating Instructions Manual

Contents

Panasonic Viera TX-26LXD71F Operating Instructions Manual Manual pdf 22 page image

FAQs, etc.• Specifications• Frequently Asked QuestionsTX-26LXD71F TX-32LXD71FPower Source AC 220-240 V, 50 / 60 HzPowerConsumptionAverage use 102 W 138 WStandby condition 0.4 W (Without DVB recording) / 19 W (With DVB recording)DisplaypanelAspect Ratio 16:9Visible screen size 66 cm (diagonal) 80 cm (diagonal)575 mm (W) × 323 mm (H) 697 mm (W) × 392 mm (H)Number of pixels 1,049,088 (1,366 (W) × 768 (H))SoundSpeaker 120 mm × 60 mm × 2 pcsAudio Output 20 W (10 W + 10 W)Headphones M3 (3.5 mm) stereo mini Jack × 1PC signalsVGA, SVGA, XGASXGA ······ (compressed)Horizontal scanning frequency 31 - 69 kHzVertical scanning frequency 59 - 86 HzReceiving Systems /Band namePAL B, G, H, I, SECAM B, G, SECAM L / L’VHF E2 - E12 VHF H1 - H2 (ITALY)VHF A - H (ITALY) UHF E21 - E69CATV (S01 - S05) CATV S1 - S10 (M1 - M10)CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)PAL D, K, SECAM D, KVHF R1 - R2 VHF R3 - R5VHF R6 - R12 UHF E21 - E69PAL 525/60 Playback of NTSC tape from some PAL Video recorders (VCR)DVB Digital terrestrial services via VHF / UHF aerial input.M.NTSC Playback from M. NTSC Video recorders (VCR)NTSC (AV input only) Playback from NTSC Video recorders (VCR)• TV signals may not be received in some areas.Aerial - Rear VHF / UHFOperating Conditions Temperature : 0 °C - 35 °CHumidity : 20 % - 80 % RH (non-condensing)Connection TerminalsAV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)AV3VIDEO RCA PIN Type × 1 1.0 V[p-p] (75 Ω)S-VIDEO Mini DIN 4-pin Y:1.0 V[p-p] (75 Ω) C:0.286 V[p-p] (75 Ω)AUDIO L - R RCA PIN Type × 2 0.5 V[rms]COMPONENT VIDEO Y 1.0 V[p-p] (including synchronization)PB , PR ±0.35 V[p-p]AUDIO L - R RCA PIN Type × 2 0.5 V[rms]OthersHDMI1 / 2 TYPE A ConnectorsPC HIGH-DENSITY D-SUB 15PIN R,G,B/0.7 V[p-p] (75 Ω)HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)Output AUDIO L - R RCA PIN Type × 2 0.5 V[rms] (high impedance)Dimensions ( W × H × D ) 657 mm × 525 mm × 216 mm (With TV Stand)657 mm × 473 mm × 117 mm (TV only) 791 mm × 615 mm × 248 mm (With TV Stand)791 mm × 563 mm × 117 mm (TV only)Mass 14.0 k Net 17.5 k Net42 43Problem ActionsScreen Sound HDMIChaotic image, noisy • Set “P-NR” in the Picture Menu (to remove noise). (p. 20)• Check nearby electrical products(car, motorcycle, fluorescent lamp).No image can bedisplayed • Is “Colour” or “Contrast” in the Picture Menu set to the minimum?(p. 20)• Check Colour system. (p. 27)Blurry or distorted image(no sound or low volume) • Reset channels. (p. 27)No sound is produced • Is “Sound mute” active? (p. 7)• Is the volume set to the minimum?Sound level is lowor sound is distorted • Sound signal reception may be deteriorated.• Set “MPX” (p. 20) in the Sound Menu to “Mono”. (Analogue)• Check Sound system. (p. 27)Sound is unusual• Set the sound setting of the connected equipment to“2ch L.PCM”.• Check the “HDMI1 Input” setting in the Sound Menu. (p. 20)• If digital sound connection has a problem, select analogue soundconnection. (p. 33)Pictures from externalequipment are unusualwhen the equipment isconnected via HDMI• Is the HDMI cable connected properly? (p. 36)• Turn Off the TV and equipment, then turn them On again.• Check an input signal from the equipment. (p. 40)• Use an equipment compliant with EIA/CEA-861/861B.Unusual image is displayed • Turn off the TV with Mains power On / Off switch, then turn it onagain.TV goes into“Standby mode” • Off Timer function is activated.• The TV enters “Standby mode” about 30 min.after broadcastingends.The remote controldoes not work • Are the batteries installed correctly? (p. 6)• Has the TV been switched On?OtherDVB• Due to the digital reception technologies involved, quality of the DTV signals may be relatively low insome cases, despite good reception of analogue programmes.Interference orfrozen / disappearingimage in DVB• Check “DVB Signal Condition”. (p. 28)If “Signal Quality” or “Signal Strength” are displayed in red,check aerial.If problem persists, consult your local Panasonic dealer.• Turn the TV off with the Mains power On / Off switch, then turnit On again.Unable to receive signalswith a high-performanceaerial• Install an aerial individually for the TV and VCR(or use a splitter).TVVCRAerialInputterminalAerial OutputAerial Output Aerial Input(Individual aerial)(Individual aerial)SplitterFAQs SpecificationsNote• Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.• This equipment complies with the EMC standards listed below.EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.• This TV supports “HDAVI Control 2” function.

/ 22

Related manuals for Panasonic Viera TX-26LXD71F